Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 225

Страница: 225 / 378

Measurements

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

225

The middle value is bounded by the values set for lower and upper thresholds.

The default middle threshold is 50% or 1.20 V.

•

If threshold

Type

is set to

, the middle threshold value can be set from 6% to

94%.

Press the

Upper

softkey; then, turn the Entry knob to set the upper

measurement threshold value.

Decreasing the upper value below the set middle value will automatically

decrease the middle value to be less than the upper value. The default upper

threshold is 90% or 1.50 V.

•

If threshold

Type

is set to

, the upper threshold value can be set from 7% to

95%.

Measurement Window with Zoom Display

When the zoomed time base is displayed, you can choose whether measurements

are made in the Main window portion of the display or the Zoom window portion of

the display.

Press the

[Meas]

key.

In the Measurement Menu, press the

Settings

softkey.

In the Measurement Settings Menu, press the

Meas Window

softkey; then, turn

the Entry knob to select from:

•

Auto Select

— The measurement is attempted in the lower, Zoom window; if it

cannot be made there, the upper, Main window is used.

•

Main

— The measurement window is the upper, Main window.

•

Zoom

— The measurement window is the lower, Zoom window.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды