Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 129

Страница: 129 / 378

Display Settings

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

129

Press

[Display]

Press the

Grid

softkey; then, turn the Entry knob

to select the grid type.

To adjust the grid intensity

To adjust the display grid (graticule) intensity:

Press

[Display]

Press the

Intensity

softkey; then, turn the Entry knob

to change the

intensity of the displayed grid.

The intensity level is shown in the

Intensity

softkey and is adjustable from 0 to

100%.

Each major vertical division in the grid corresponds to the vertical sensitivity

shown in the status line at the top of the display.

Each major horizontal division in the grid corresponds to the time/div shown in the

status line at the top of the display.

To freeze the display

To freeze the display without stopping running acquisitions, you must configure

the

[Quick Action]

key. See

"Configuring the [Quick Action] Key"

on page 291.

Once the

[Quick Action]

key has been configured, press it to freeze the display.

To un-freeze the display, press

[Quick Action]

again.

Manual cursors can be used on the frozen display.

Many activities, such as adjusting the trigger level, adjusting vertical or horizontal

settings, or saving data will un-freeze the display.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды