Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 110

Страница: 110 / 378

110

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Digital Channels

To display digital channels as a bus

Digital channels may be grouped and displayed as a bus, with each bus value

displayed at the bottom of the display in hex or binary. You can create up to two

buses. To configure and display each bus, press the

[Digital]

key on the front panel.

Then press the

Bus

softkey.

Next, select a bus. Rotate the Entry knob, then press the Entry knob or the

Bus1/Bus2

softkey to switch it on.

Use the

Channel

softkey and the Entry knob to select individual channels to be

included in the bus. You can rotate the Entry knob and push it or push the softkey

to select channels. You can also press the

Select/Deselect D7-D0

softkey to include

or exclude groups of eight channels in each bus.

If the bus display is blank, completely white, or if the display includes "...", you

need to expand the horizontal scale to allow space for the data to be shown, or

use the cursors to display the values (see

"Using cursors to read bus values"

page 111).

The

Base

softkey lets you choose to display the bus values in hex or binary.

The buses are shown at the bottom of the display.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды