manualshive.com logo in svg

Keysight Technologies B1505A, Руководство по настройке

Поделиться
Скачать
Keysight Technologies B1505A Скачать руководство пользователя страница 82

1-74

Keysight B1505A Configuration and Connection Guide

Configuration Guide
Note for 4142B Users

Note for 4142B Users

The B1505A expands the maximum measurement range up to 40 A/3000 V from the range 
10 A/1000 V covered by Keysight 4142B Modular DC Source/Monitor.

Because of the following reasons, the measurement setup and environments for the 4142B 
cannot be used with the B1505A. The test fixture and the connection path from connector 
plate to wafer prober must be designed, changed, or remade for the B1505A.

•

Test fixture 16088A/B designed for the 4142B, cannot be used for the measurements 
over 10 A/1000 V.

•

The connection path, connectors, cabling, and wiring will not support up to 
40 A/3000 V.

•

Connector types are different from the 4142B.

Table 1-32

Considering Connector Types

4142B

B1505A

High current connector

Dual triaxial

BNC and triaxial

High voltage connector

BNC and screwed-triaxial

HV triaxial

Interlock connector

BNC

6-pin

BNC female 
bulkhead-type 

Triax. female 
bulkhead-type 

Interlock receptacle: Agilent P/N:1252-1419 
or Hirose, HR10A-7R-6S

HV Triax.  female bulkhead-
type (N1254A-500)

Keysight

Содержание B1505A











































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды