manualshive.com logo in svg

Keysight Technologies B1505A, Руководство по настройке

Поделиться
Скачать
Keysight Technologies B1505A Скачать руководство пользователя страница 201

Keysight B1505A Configuration and Connection Guide

5-53

Connection Guide for Wafer Prober and Your Own Test Fixture

About Cable Connections

•

For the non-Kelvin connection, the voltmeter measures the voltage drop of resistances 

r

F1

, 

R

DUT

, and 

r

F2

.

•

For the Kelvin connection, the voltmeter measures the voltage drop of resistance 

R

DUT

 

only. The impedance of the voltmeter is very high, so the voltage drop of resistances 

r

S1

 and 

r

S2

 can be ignored.

The Kelvin connection is effective even when forcing voltage. The voltage drop due to the 
residual resistance of the Force line wiring is fed back to the voltage source via a 
comparator in the Sense line. The input impedance of comparator is high, and current flow 
into the Sense line is very low. So output error is not significant if the Sense line wiring has 
a residual resistance of 10 

 or less. Therefore, the specified voltage appears at the sense 

point (point where Sense line contacts Force line)

NOTE

Kelvin connection and non-Kelvin connection

To make the Kelvin connection, use both Force and Sense terminals. Connecting the Force 
and Sense lines together at the terminal of the DUT (device under test) minimizes the 
measurement error caused by the residual resistance of the connection cables. The Kelvin 
connection is effective for the low resistance measurement and the high current 
measurement.

If you want to simplify the cable connections, open the Sense terminals and use the Force 
terminals only. This is the non-Kelvin connection. The Force terminals can be used to force 
and measure dc voltage or current.

To Connect UHVU/HVSMU/HVMCU Output

To prevent discharge and any accident, make enough space between the cable ends, also 
between the high side cable end and the shield or chassis. For example, make space of 
about 32 mm from the high side cable end for maximum 10 kV output. Also the creepage 
distance must be more than 100 mm for 10 kV.

Figure 5-28

Space around Cable End

To UHVU High

To UHVU Low

DUT

Shield

Signal line

Insulator

SHV Cable

UHV Cable

Insulator

¡

32 mm for 10 kV

¡

100 mm for 10 kV

Содержание B1505A











































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды