manualshive.com logo in svg

Keysight Technologies B1505A, Руководство по настройке

Поделиться
Скачать
Keysight Technologies B1505A Скачать руководство пользователя страница 175

Keysight B1505A Configuration and Connection Guide

5-27

Connection Guide for Wafer Prober and Your Own Test Fixture

To Connect Module Selector

To Connect Module Selector

Keysight N1258A module selector is used to switch the measurement resource connected 
to the device under test (DUT) automatically. The measurement resource will be 
HP/MPSMU, HVSMU/HVMCU, or HC/DHCSMU. One selector provides one switching 
channel. Also the selector has built-in GNDU protection adapter, built-in HPSMU 
protection adapter, and built-in HCSMU Kelvin adapter. 

The N1258A should be installed near your DUT interface as shown in 

Table 5-3 on page 

5-7

. Also see figures 

5-11

 and 

5-12

.

The output cable connection is effective for all measurement performed by the modules 
connected to the Input terminals. Connection change is not required. The module selector 
switching status is indicated by the Status indicator mounted on the front panel. See 

Table 

5-22 on page 5-31

. 

Figure 5-10

Module Selector Circuit Diagram and Connections

CAUTION

The GNDU can sink current of up to 4.2 A. Use 16493L GNDU cable to connect the 
GNDU to the N1258A.

Do 

not

 use normal triaxial cable (16494A) because the maximum current rating of the 

cable is 1 A.

CAUTION

Maximum current must be ± 30 A to prevent the module selector from performance 
degradation and failure.

NOTE

Using Dual HCSMU (DHCSMU)

DHCSMU can be configured by two HCSMU modules installed in one B1505A and 
connected to the 16493S-021 Dual HCSMU combination adapter. See 

"To Connect Dual 

HCSMU Adapter"

 for connection. The output connectors are compatible with HCSMU.

Front view

DUT high terminal

DUT high

HPSMU

DUT low

Module Selector

Open

High

HVSMU

HCSMU

GNDU

Low

AC power

B1505A Digital I/O

HCSMU Force+Sense
HPSMU Force+Sense
GNDU Force+Sense
HVSMU Force

Rear view

DUT low terminal

Open

100 k

W

Содержание B1505A











































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды