Keysight Technologies AC6801B Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 197

background image

Connecting the Power Cord

The power cord used with the product varies depending on the model. This product complies with IEC
Overvoltage Category II (energy-consuming equipment supplied from a fixed installation).

The AC6801B line cord has a molded plug on both ends.
The AC6802B is a single-phase, cord-connected device that requires a plug
and cord set.
The AC6802B line cord must have a plug on the utility side; you cannot hard
wire the instrument to the utility.

Possible Electric Shock

This product is an IEC Safety Class I equipment (equipment with a protective
conductor terminal). Be sure to ground (earth) the unit.

Connect the protective conductor terminal to earth ground.

AC6801B

Connect the power cord to the AC connector on the back of the instrument. Then connect the other
end to a properly grounded power outlet. You will use this plug to disconnect from mains power.

Use the supplied power cord to connect to the AC line. If the supplied power cord cannot be used due
to the rated voltage or the plug shape, have a qualified engineer replace it with an appropriate power
cord of length 3 m or less. If obtaining a power cord is difficult,

contact Keysight

The power cord with a plug can be used to disconnect the instrument from the AC line in an
emergency. Connect the plug to an easily accessible power outlet so that the plug can be removed
from the outlet at any time. Be sure to allow enough space around the power outlet.

To connect the power cord:

1. Check that the AC power supply meets the instrument's nominal input rating, which is any nominal
voltage from 100 to 120 VAC or 200 to 240 VAC. The frequency is 50 or 60 Hz.

Large voltage distortion on the AC power line can lead to malfunction. Do not
connect the instrument to a generator or a similar device.

2. Check that the power switch is turned off.

3. Connect the power cord to the AC input receptacle on the rear panel.

4. Insert the power plug into an outlet.

1 Getting Started

28

Keysight AC6800B Series Operating and Service Guide

«
...
26
27
28
29
30
...
»

Содержание AC6801B






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AC6801B

Бренд: S&C Страницы: 24

Бренд: Pacific Power Source Страницы: 463

Бренд: Tripp Lite Страницы: 3

Бренд: Phonic Страницы: 8

Бренд: M-system Страницы: 3

Бренд: Pacific Страницы: 43

Бренд: Baumuller Страницы: 62

Бренд: KEMET Страницы: 2

Бренд: dehn Страницы: 32

Бренд: GW Instek Страницы: 76

Бренд: Lab 12 Страницы: 10

Бренд: EuroLite Страницы: 16

Бренд: EuroLite Страницы: 16

Бренд: EuroLite Страницы: 16

Бренд: EuroLite Страницы: 16

Бренд: Bachmann Страницы: 3

Бренд: Atlas Страницы: 12

POWER STAR LiFE

Бренд: PSC Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды