manualshive.com logo in svg

Keysight Technologies 85309B LO/IF, Руководство пользователя и сервисное руководство

Поделиться
Скачать
Keysight Technologies 85309B LO/IF Скачать руководство пользователя страница 26

2-8                                                                                         Keysight 85309B User’s and Service Guide

Operating Information
85309B Rear Panel Features

2-

Receiver Connector Group

The four BNC connectors in this group, J9 TEST 1 IF OUT (standard), J1O 
REFERENCE IF OUT, J12 TEST 2 IF OUT (option 001 or 401), and J14 TEST 3 IF 
OUT (option 002 or 402), output the test and reference IF signals to the 

receiver.

J9 TEST 1 IF OUT (standard). This connector sends the test mixer's IF signal to 
the receiver. Generally, this signal is connected, through the 
BNC-to-RECEIVER ADAPTER cable, to the receiver b2 input.

J1O REFERENCE IF OUT. This connector sends the reference mixer's IF signal 
to the receiver. Generally, this signal is connected, through the 
BNC-to-RECEIVER ADAPTER cable, to a1 on the receiver.

J12 TEST 2 IF OUT (option 001 or 401). This connector sends the test mixer's IF 
signal to the receiver. Generally, this signal is connected, through the 
BNC-to-RECEIVER ADAPTER cable, to the receiver b1 input.

J14 TEST 3 IF OUT (option 002 or 402). This connector sends the test mixer's IF 

signal to the receiver. Generally, this signal is connected, through the 
BNC-to-RECEIVER ADAPTER cable, to the receiver a2 input.

J7 and J8 (Using Non-Diplexed Mixers). J7 and J8 allow you to use a 
non-diplexed test mixer (a mixer that has separate connections for the LO and 
IF signal). This is done by removing the Type-N jumper that normally connects 
J7 and J8. With the jumper removed, make the following connections to your 

test mixer:

If you are using a test mixer that uses a single LO/IF connection and a diplexer, 
always place the supplied Type-N jumper between J7 and J8.

J15 HIGH/LOW BAND SELECT (option 40x). Allows external control of the 
HIGH/LOW BAND SELECT feature when the front panel BAND SELECTION 
knob is in the EXT position. See 

“BAND SELECTION (Option 40x Only)” on 

page 4

. TTL high (+5 V) selects HIGH band; TTL low (0 V) selects LOW band.

Table 2-1 

Connections for Non-Diplexed Mixers

85309B Connector

Connection

J3 TEST LO/IF

Mixer LO INPUT

J7 TEST IF IN

Mixer IF OUTPUT

J8 DIPLEXER IF OUT

50-ohm Load

a

a. It is recommended that you place a 50-ohm load on this connector.

Содержание 85309B LO/IF

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды