Keysight Technologies 85058V Скачать руководство пользователя страница 9

Страница: 9 / 58

85058V

1-3

General Information

Incoming Inspection

Installation of the Calibration Definitions

The calibration definitions for the kit should be permanently installed in the internal memory or

hard disk of the PNA. They may already be resident within the analyzer, or you can download

them from Keysight’s Calibration Kit Definitions Web page at

ht tp://na.support.keysight.com/pna/caldefs/stddefs.html

In addition

the calibration definitions

may be entered manually from the front panel. Refer to your PNA Help system for instructions.

Equipment Required but Not Supplied

Some items are required or recommended for successful operation of your kit, but are not

supplied with the kit. Refer to

Table 6-3 on page 6-7

for a list of these items and for ordering

information.

Incoming Inspection

Verify that the shipment is complete by referring to the contents list in the shipping container.
Check for damage. The foam-lined storage case provides protection during shipping. Verify

that this case and its contents are not damaged.
If the case or any device appears damaged, or if the shipment is incomplete, contact Keysight -

refer to

page 5-6

. Keysight will arrange for repair or replacement of incomplete or damaged

shipments without waiting for a settlement from the transportation company. Refer to

“Returning a Kit or Device to Keysight Technologies” on page 5-5

for instructions.

Содержание 85058V



























































Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды

Keysight Technologies 85058V, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды