Keysight Technologies 85058V Скачать руководство пользователя страница 23

Страница: 23 / 58

85058V

3-3

Use, Maintenance, and Care of the Devices

Visual Inspection

Visual inspection and, if necessary, cleaning should be done every time a connection is made.

Metal particles from the connector threads may fall into the connector when it is disconnected.

CAUTION

Devices with damaged connectors should be immediately discarded or clearly

marked and set aside for repair. A damaged device will in turn damage any good

connector to which it is attached. Determine the cause of the damage before

connecting a new, undamaged connector in the same configuration.

In some cases, magnification is necessary to see damage to a connector; a magnifying device

with a magnification of





is recommended. However, not all defects that are visible only

under magnification will affect the electrical performance of the connector. Use the following

guidelines when evaluating the integrity of a connector.

Look for Obvious Defects and Damage First

Examine the connectors first for obvious defects or damage: badly worn plating on the

connector interface, deformed threads or bent, broken, or misaligned center conductors.

Connector nuts should move smoothly and be free of burrs, loose metal particles, and rough

spots.

What Causes Connector Wear?

Connector wear is caused by connecting and disconnecting the devices. The more use a

connector gets, the faster it wears and degrades. The wear is greatly accelerated when

connectors are not kept clean, or are not connected properly.
Connector wear eventually degrades performance of the device. Verification devices should

have a long life if their use is on the order of a few times per week. Replace devices with worn

connectors.
The test port connectors on the PNA test set may have many connections each day, and are,

therefore, more subject to wear. It is recommended that an adapter be used as a test port saver

to minimize the wear on the test set’s test port connectors.

Connector Contacts

See

Figure 3-2 on page 3-4

for visual guidelines when evaluating the contact integrity of a

connector.

NOTE

Notice the location of the cross hairs in relationship to the center of the figures.

Содержание 85058V



























































Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды

Keysight Technologies 85058V, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды