Keysight Technologies 85058V Скачать руководство пользователя страница 14

Страница: 14 / 58

2- 2

85058V

Specifications

Environmental Requirements

Temperature—What To Watch Out For

Due to the thermal properties of the devices, electrical characteristics will change with

temperature. Therefore, the operating temperature is a critical factor in their performance, and

must be stable before use.

IMPORTANT

Avoid unnecessary handling of the devices during use because your fingers are a

heat source.

Table 2-1 Environmental Requirements

Parameter

Required Values/Ranges

Temperature

Operating

a. The temperature range over which the calibration standards maintain conformance to their

specifications.

+20



C to +26



C (+68



F to +79



Storage

–40



C to +75



(–40



F to +167



Error-corrected range

b. The allowable network analyzer ambient temperature drift during measurement calibration and during

measurements when the network analyzer error correction is turned on. Also, the range over which the

network analyzer maintains its specified performance while correction is turned on.





C (1.8



F) of measurement calibration temperature

Altitude

Operating

< 4,500 meters (ª15,000 feet)

Storage

< 15,000 meters (ª50,000 feet)

Relative humidity

Always non–condensing

Operating

0 to 80% (26



C maximum dry bulb)

Storage

0 to 90%

Содержание 85058V



























































Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды

Keysight Technologies 85058V, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 85058V

Отзывы:

Похожие инструкции для 85058V

Бренды по названию

Популярные бренды