Keysight Technologies 8480 Series Скачать руководство пользователя страница 65

Страница: 65 / 99

Service

Keysight 8480 Series Operating and Service Manual

FET Balance Adjustment

The FET balance adjustment should be performed if the wires connecting J1 (the

sensor cable connector) to A2 (the power sensor board assembly) have been

moved. If you have replaced A2 assembly or moved the wires during

troubleshooting you need to perform this adjustment.

Equipment Required

– Oscilloscope
– BNC cables (2 required)
– Power meter (modified as described in

Appendix A

)

Test Description

This test applies to both thermocouple and diode power sensors. Among the

required equipment is a modified E4418B Power Meter. The High Gain output of

the power meter is connected to Channel 1 of an oscilloscope, and the Chop

Output (220Hz square wave) of the power meter is connected to the oscilloscope

trigger - the High Gain output is the amplified version of the Power Sensor

chopped signal. Ideally, when no RF power is applied to the power sensor, the

High Gain output signal displayed on the oscilloscope is a straight line. If there is

a sensor offset, the offset signal is visible on the oscilloscope as a square wave

(chopped signal). Also, a switching transient (spike) usually occurs at the edge of

the chopped signal, due to the switching of the FET in the Power Sensor. Sensor

offset and spike balance are affected by the relative positions of the wires

connected to pins G and H of connector J1. One wire is black and white; the other

is brown and white. Moving the black and white wire adjusts the amplitude of the

switching transient (spike). Moving the brown and white wire changes the offset.

Once positioned, care must be taken not to displace these wires. To correctly

position these wires, perform the “FET Balance Procedure” on page 66.

NOTE

You do not need to perform a FET balance adjustment after an A1 bulkhead

assembly replacement, if the wires between J1 and A2 have not been disturbed.

Содержание 8480 Series




































































































Результаты поиска

Содержание 8480 Series

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 8480 Series

Отзывы:

Бренды по названию

Популярные бренды