manualshive.com logo in svg

Keysight Technologies 8480 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Keysight Technologies 8480 Series Скачать руководство пользователя страница 44

2

General Information

44

Keysight 8480 Series Operating and Service Manual

Zero set performance verification

This performance verification is carried out to verify that a minimal amount of 

residual offset error is present after zeroing has been performed. The offset error is 

caused by contamination from several sources including the noise of the 

device-under-test (DUT) itself. Zero set is the difference between the power levels 

indicated by the DUT, after executing zeroing and the true zero power. Ideally, this 

difference should be zero.
This performance test requires a compatible Keysight power meter with the DUT 

and a computer with the Keysight IO Libraries Suite installed.

4 to 12 GHz 

< 1.19 (0.085)

12 to 18 GHz 

< 1.25 (0.112)

18 to 26.5 GHz 

< 1.29 (0.127)

8487D

50 to 100 MHz 

< 1.19 (0.085)

0.1 to 2 GHz 

< 1.15 (0.069)

2 to 12.4 GHz 

< 1.20 (0.091)

12.4 to 18 GHz 

< 1.29 (0.127)

18 to 34 GHz 

< 1.37 (0.156)

34 to 40 GHz 

< 1.61 (0.234)

40 to 45 GHz 

< 1.86 (0.301)

45 to 50 GHz 

< 1.89 (0.310)

Table 2-1

Power sensor SWR and reflection coefficient

Frequency

Maximum SWR (reflection coefficient) Actual measurement

System specification:

±50 nW (for all 848xA) and 

±20 pW (for all 848xD), tested at 50 MHz

Recommended power meter: EPM series power meters (E4418B and E4419B), 

the EPM-P series power meters (E4416A and 

E4417A)

Содержание 8480 Series




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды