Keyscan CA250B Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 140

background image

Keyscan Inc. – Technical Guide (PC109x - 04.15)

22

Grounding Communication Cable Shield

When terminating the communication cable in the metal enclosure, ensure that the shield is insulated and
connected to the ground lug. Keyscan suggests Alpha PVC 10516 – 16 AWG clear tubing or a comparable
tubing to insulate the shield. Do not connect the shield to GND on a communication terminal block.

Ground Lugs

The metal enclosure includes one ground lug pre-mounted near the top and one spare ground lug, which can
be mounted to one of the available ground lug studs. You can re-locate the ground lug inside the metal
enclosure to minimize the length of shield used.

Note

Keep all shield wires and cables away from the control board.

Control Board – Mounting Locations

The following diagrams illustrate the mounting positions for control board series CA250, CA4500, CA8500,
EC1500 and EC2500 units. Illustrations also show mounting positions for communication boards and output
control boards (OCB-8). Different door control board series – CA250, CA4500, and CA8500 – can be used
within the same communication loop.

CA & EC Control Board Dimensions



Width 20.35 cm (8.01 inches)



Height 28.9 cm (11.38 inches)

Operating Environment – ACUs & ECUs



Temperatures: 41°F to 120°F (5°C to 49°C)



Humidity: 0% to 90% R.H., non-condensing

Important

Do not mount close to high voltage equipment.

«
...
20
21
22
23
24
...
»

Содержание CA250B













































































































































Отзывы:

Нет отзывов

Похожие инструкции для CA250B

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: U-Prox Страницы: 31

Бренд: Warren Controls Страницы: 16

Бренд: Wavelink Страницы: 69

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Rane Страницы: 2

Бренд: Tamas Страницы: 12

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: D+H Страницы: 2

Бренд: Cardin Elettronica Страницы: 56

Бренд: Linak Страницы: 2

Бренд: Westfalia Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды