EN - 18
User Manual
5.3 ADJUSTING THE DRIVE EFFECT
The Drive effect can be adjusted by modifying the following parameters:
-
244B
TYPE (“
tyP
” on the display): select the type of distortion.
245B
DRIVE TYPE
1.
Press the [DRIVE] button until the display shows the message “
tyP
”.
2.
Press [VALUE +] or [VALUE -] to switch between:
-
246B
“
Cls
”: CLASSIC mode, simulating the distortion of the internal valve amplifier of the classic rotating
speaker.
-
247B
“
rCk
”: ROCK mode, simulating the sharper sound of guitar valve amplifiers from the '70s.
For more information on the Drive effect, see par. 4.6.
5.4 CONFIGURING THE PEDALS SECTION
The Pedals section can be configuerd by modifying the following parameters:
-
250B
TO LOWER (“
tLr
” on the display): activate the PEDALS TO LOWER function.
-
251B
DIRECT (“
drt
” on the display): activate the PEDALS DIRECT function.
-
252B
SUSTAIN (“
tyP
” on the display): set the PEDALS SUSTAIN.
-
253B
SPLIT POINT LOWER/PEDALS (“
sLP
” on the display): set the Split Point between the Lower and Pedals
sections.
254B
PEDALS TO LOWER
1.
Press the [PEDALS] button until the display shows the message
“
tLr
”.
2.
Press [VALUE +] or [VALUE -] to select:
-
255B
“
off
”: PEDALS TO LOWER function disabled.
-
256B
“
LAy
”: activate the PEDALS TO LOWER function in LAYER mode. In this mode the Pedals section can
be played on the same keyboard area of Lower section up to the Split Point set through the SPLIT
POINT LOWER / PEDALS function. The keys in this area play both the Lower and Pedals sounds.
-
257B
“
sPL
”: activate the PEDALS TO LOWER function in SPLIT mode. In this mode the Pedals section can
be played on the same keys as the Lower section up to the Split Point, set through the SPLIT POINT
LOWER / PEDALS function. The keys to the left of the Split Point only play the drawbars of the Pedals
section, while those to the right of the Split point only play the drawbars of the Lower section.
For more information on the PEDALS TO LOWER function, see par. 4.1.
258B
PEDALS DIRECT
1.
Press the [PEDALS] button until the display shows the message
“
drt
”.
2.
Press [VALUE +] or [VALUE -] to switch between.
-
259B
“
off
”: the sound of the Pedals section is sent to the [LEFT], [RIGHT] and [PHONES] connectors.
-
260B
“
on
”: the sound of the Pedals section is only sent to the [PEDALS] connector.
261B
PEDALS SUSTAIN
1.
Press the [PEDALS] button until the display shows the message “
sUs
”.
2.
Press [VALUE +] or [VALUE -] to adjust the value. When the value is “
0
”
the drawbars of the pedalboard
play both the root note and the harmonics, and the decay is immediate (decay time is zero). When the
value is between “
1
” and “
127
” (maximum) the pedalboard drawbars become monophonic and the 8'
drawbar only generates the root note. As the value increases, so does the decay time of the notes.
262B
SPLIT POINT LOWER/PEDALS
1.
Press the [PEDALS] button until the display shows the message “
sLP
”.
2.
Press [VALUE +] or [VALUE -] to select a key as Split Point between the Lower and Pedals sections when
the function PEDALS TO LOWER is in LAYER or SPLIT mode. Available values range from "
C1
" to "
C3
".
