To next light
Input from Controller
Intensity Tuning Dial
Unit Link Cable
Spectrum Tuning Dial
INSTALLATION GUIDE
PARTS DIAGRAM
TROUBLESHOOTING GUIDE
Problem
Light doesn’t turn ON
Unit is flickering
Solution
Make sure the unit is connected to the power supply and the power
supply is connected to an outlet with the correct specifications.
Make sure you are using a power supply with the correct specifications.
Make sure to operate the unit in a room at 104°F / 40°C or lower to
prevent overheating.
Make sure electrical power is available to the AC outlet being used.
Make sure the power supply has the right specifications.
Make sure the device is operating within the specified operating
temperature range (below 104°F or 40°C). If the unit overheats, it will
automatically shut down.
H80 Tuna Flora
PRODUCT SPECIFICATIONS
Illuminator
Listed Power Supply
Power Consumption 15W maximum
24VDC
Input Voltage
Input
Output
100-240VAC, 50-60Hz
24VDC, maximum 1A
Controllability
Multiple Kessil lights with 0-10V ports can be controlled
either manually or by an external 0-10V controller.
SAFETY INSTRUCTIONS
1.
DO NOT
use a power supply that does
not meet the specifications. This is a fire
hazard and may lead to unit failure.
2.
DO NOT
use outdoors. This unit is
intended for indoor use only.
3.
DO NOT
expose unit to an extremely
humid environment or submerge in
water. This may lead to unit failure.
4.
DO NOT
place unit in close contact with
any other objects while powered on
because unit may overheat.
5.
KEEP
Lens (E) away from sharp
objects. This may break the lens and
lead to unit failure.
6.
DO NOT
cover or place objects on the
DC Power Supply (G). It should not be
contained in an airtight space.
MAINTENANCE
1. Keep the unit clear of dust. To clean, unplug the unit and use a clean, dry cloth to
remove accumulated dust from between each Heat Sink Fin (D).
2. Keep the Lens (E) clean. If the lens becomes contaminated with water, dust, or other
particles, unplug the unit and clean the lens with isopropyl alcohol. Wet a cotton swab
or a napkin in isopropyl alcohol, gently wipe the surface of the lens and let dry.
CABLES
Available cables:
• Control Cable (Please consult kessil.com
for list of available cables and compatible
controllers).
• Unit Link Cable (male/male with 3.5 mm
stereo jack).
• Control Extension Cable (6' male/female
with 3.5 mm stereo jack).
STARTING A CHAIN
Connect two or more lights with the Unit
Link Cable, as shown above.
CONTROL METHODS
There are two ways to control a chain of lights:
1. With an external controller.
2. Without external controller (Tuning Dials on
the first light control all other lights in chain).
Each light has its own independent power
supply. Any number of lights can be daisy
chained together without degradation of
signal. However, in longer chains a slight
delay in response may occur. Manual tuning
is disabled when input cable is plugged in.
INSTRUCTIONS DE SECURITE
1. N'UTILISEZ PAS d'adaptateur
d'alimentation qui ne satisfait pas aux
exigences.
Il y aurait un risque d’incendie
et de dommages de l’unité.
2. NE PAS UTILISER à l’extérieur. Cette
unité est prévue pour une utilisation en
intérieur.
3. N’EXPOSEZ PAS l’unité à un
environnement extrêmement humide ou
ne submergez pas l’unité dans l’eau. Cela
pourrait endommager l’unité.
4.
NE PLACEZ PAS l'illuminateur dans
Contact étroit avec tout autreObjets
pendant qu'ils sont allumés parce que
l'unité peut surchauffer.
5. GARDEZ la Lentille (E) à l‘écart des objets
pointus. Les objets pointus pourraient
casser la lentille et endommager l’unité.
6. NE RECOUVRE PAS, ou ne placez pas
d’objet sur DC l'adaptateur d'alimentation
(G). Il ne doit pas se trouver dans un
espace fermé.
1. Remove contents from package.
2. Hang the H80 at least 4 inches above
the plants/tank.
3. Connect Power Cord (A) to the specified
DC Power Supply (G).
4. Plug the power supply into an outlet with
the correct specifications (see product
specifications for more information).
5. Using the H80's Intensity Tuning Dial (F)
and Spectrum Tuning Dial (B), set the
light to the desired setting. H80 has four
specifically designed spectrums (BLUE,
GROW, BLOOM, RED)(see kessil.com
for detailed spectrum information and
application).
6. The ports between the dials can be
connected to an external 0~10V controller.
Please consult your controller's owner's
manual for more information.
A
B
F
D
A. Power Cord
B. Spectrum Tuning Dial
C. 0-10V Controller Ports
D. Heat Sink Fin
E. Lens
F. Intensity Tuning Dial
G. DC Power Supply
C
G
Optional Accessories
For other accessories, please visit www.kessil.com.
Remove the two screws on the back of H80,
and use them to secure Top Mounting Adapter
(H) to H80, then use two wood screws (I) to
mount them.
Top Mounting Adapter
OWNER’S MANUAL
LED ILLUMINATOR
Mini A-Series Gooseneck
(Gooseneck Length = 10 inches)
E
A DiCon Brand
ver. A1
H
I
