Kessel Aqualift Comfort 230V Mono, Руководство пользователя

Страница: 29 / 108

Float switch, Mono/Duo
Check whether the system is a Mono or a Duo system.
Define level for ON 1, if applicable, ON 2 (Duo) and OFF.
KESSEL recommends providing an alarm level for the
items named above.
If a float switch fails, the float switches can be swapped
temporarily so that the OFF level does not have to be
used. The switching off is then set in the control unit via
the post run time of the pumps. See
| 3.1.2 Post
run time |
under the Settings menu and Parame-
ter selection. This procedure is not suitable for contin-
uous operation, as dry running of the pumps should be
avoided.
Position Terminal assignment
1 Alarm level
2 ON 2 (Duo only)
3 ON 1
4 OFF
a b c d e f a b c d e f
PC PC
Tx RS Rx RG Tx RS Rx RG GND GND
or or or or or or or or or or
US B US B
cable cable
US B US B
fash drive fash drive MODEM MODEM
2 1 2 1
(/(&752'( (/(&752'(
I1 I1 I2 I3 I2 I3 I4 I4
- -
+ +
ALARM ALARM
- - - - - - gn gn ws ws br br bl bl gn gn bl bl sw sw gn gn bl bl sw sw sw sw bl bl
2 2
g g
h h
I1 I2 I3 I4
1
3
4
2
4 3 2 1
Fig. 1: Float switches Duo
a b c d e f a b c d e f
PC PC
Tx RS Rx RG Tx RS Rx RG GND GND
or or or or or or or or or or
US B US B
cable cable
US B US B
fash drive fash drive
MODEM MODEM
2 1 2 1
(/(&752'( (/(&752'(
I1 I1 I2 I3 I2 I3 I4 I4
- -
+ +
ALARM ALARM - - - - - - gn gn ws ws br br bl bl gn gn bl bl sw sw gn gn bl bl sw sw sw sw bl bl
2 2
g g
h h
1
3
4
I1 I2 I3
Fig. 2: Float switches Mono
Conductivity probes
A maximum of 4 conductivity probes can be connected to
the terminal block.
L OFF ON1 ON2 Alarm
Terminal block* 1 2 3 4 5
1 3-contact probe,
vertical
BL WS SW
2 2-contact probe,
horizontal
x x
3 2-contact probe,
vertical
x x
4 3-contact probe,
horizontal
x x x
* Connection corresponds to cable labelling
1
PC PC
Tx RS Rx RG Tx RS Rx RG GND GND
or or or or or or or or or or
USB USB
cable cable
USB USB
fash drive fash drive
MODEM MODEM
2 1 2 1
(/(&752'( (/(&752'(
I1 I1 I2 I3 I2 I3 I4 I4
- -
+ +
ALARM ALARM - - - - - - gn gn ws ws br br bl bl gn gn bl bl sw sw gn gn bl bl sw sw sw sw bl bl
a b c d e f a b c d e f
PC PC
Tx RS Rx RG Tx RS Rx RG GND GND
or or or or or or or or or or
USB USB
cable cable
USB USB
fash drive fash drive
MODEM MODEM
2 1 2 1
(/(&752'( (/(&752'(
I1 I1 I2 I3 I2 I3 I4 I4 - - + +
ALARM ALARM
- - - - - - gn gn ws ws br br bl bl gn gn bl bl sw sw gn gn bl bl sw sw sw sw bl bl
2 2
g g
h h
2 3 4 5
4 3 2 1
- - -
Duo
4.5 Further connection possibilities
TeleControl GSM modem
Mount the TeleControl modem (art. no. 28792) as described in the corresponding installation instructions 434-033.
Routing the USB connection out
To ensure that the USB connection on the printed board can be accessed without opening the housing, a USB housing
socket with cable and connector for installation in the housing of the control unit can be ordered from KESSEL (art. no.
28785).
Diverse accessories - control units
External audible alarm art. no. 20162
Warning beacon art. no. 97715
Potential free contact art. no. 80072 (plug-on printed board)
Potential-free contact (optional accessory)
If required, signal generators or other accessories can be connected as potential-free contacts (42 V 0.5 A). The following
terminals are available for these:
Warning (event is displayed - e.g. alarm level exceeded) -normally closed-
Fault (fatal error - e.g. in electrical connection or safety systems) -normally open-
In the event of a warning, the operating reliability of the system is usually not immediately at risk; however, the system
should be subjected to maintenance or checking by a competent person without delay. In the event of a fault, the function of
the system can be directly impaired, there is a need for direct action. Contact the service technician or emergency service.
EN
010-910_02 29 / 108