manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Руководство по установке и обслуживанию

Поделиться
Скачать
Kerlink 1LOC868-1W868-EU Скачать руководство пользователя страница 200

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 200 / 221

 

Strict confidential 

 

4.6.2.5.11

 

Four LoRa modules / dual polarization antenna 

In this configuration, the Wirnet iBTS receiver supports 2 x 32 channels. 

 

Figure 154 : Four LoRa modules / dual polarization antenna connections 

4.6.3

 

Ethernet connection 

The Wirnet iBTS gateway is supplied by a PoE injector through an Ethernet cable. 
The PoE injectors are detailed in §1.6.1. 
The recommended Ethernet cable is detailed in §1.8.4.1. It includes two RJ45 T 568A plugs 
on each side 
 

Note 1:

 The Ethernet cable is not provided with the Wirnet iBTS. 

Note 2:

 The maximum Ethernet cable length is 100m. 

 
On Wirnet iBTS side, the Ethernet RJ45 connector must be firstly inserted through the M25 
cable gland as shown on the Figure 155. 
To introduce the RJ45 cable into the cable gland, follow the procedure below: 

 

Unscrew the external nut 

 

Remove the seal 

 

Introduce the RJ45 cable into the external nut 

 

Place the seal around the RJ45 cable 

 

Introduce the RJ45 cable into the cable gland body 

 

Connect the RJ45 connector in to the PoE/LAN port of the CPU module 

 

Replace the seal in the cable gland body 

 

Screw the external nut 

 

Содержание 1LOC868-1W868-EU






























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды