Kerlink 1LOC868-1W868-EU Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 221

background image

Wirnet iBTS

Document title : Installation and
Maintenance Manual
Version : 2.0
Author : SNI
Date : 04/12/2018

Classification

This document is the strict property of Kerlink and shall not be either copied nor sent without express

written authorization of Kerlink

Internal Use

Kerlink m2m technologies reserved rights

Confidential

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

Page 161 / 221

Strict confidential

4.3

Electric distribution to the Wirnet iBTS

4.3.1

Safety

The installation must comply with EN 60728-11 (Cabled distribution systems standard -
Security).
Earthing is a key parameter for a secure installation.
Earthing of the installation is mandatory for:
-

Indoor installation parts: mains supply, PoE injector

-

Outdoor installation parts: tower, pole, Wirnet iBTS mounting kit, antennas.

Note:

none of the earthing cables required for the installation are provided by KERLINK.

A second key parameter for a secure installation is the lighting protection.
In  its  standard  configuration,  the  Wirnet  iBTS  is  provided  with  nominal  internal  surge
protections.  The  Wirnet  iBTS  gateways  are  not  warranted  by  KERLINK  in  case  of
deterioration  due  to  lighting.  Additional  surge  protections  are  recommended  in  harsh
environments.
A  lighting  rod  with  a  down  conductor  to  earth  is  strongly  recommended  in  most  of  the
applications to avoid direct impacts on the aerials (antennas and Wirnet iBTS).
The  following  picture  describes  all  the  required  cables  connections  required  for  the
installation,  including  power  supply  cables,  data  cables,  RF  coaxial  cables  and  earthing
connections.

Figure 101 : Power distribution in the installation

«
...
159
160
161
162
163
...
»

Содержание 1LOC868-1W868-EU






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LOC868-1W868-EU

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

Бренд: Enginko Страницы: 19

Linear SCP-LT8362-S-EVALZ

Бренд: Analog Devices Страницы: 8

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

Бренд: Davey Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды