manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Руководство по установке и обслуживанию

Поделиться
Скачать
Kerlink 1LOC868-1W868-EU Скачать руководство пользователя страница 153

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 153 / 221

 

Strict confidential 

 

Note 2: 

In Europe or South-Africa, if the 50dB isolation between antenna cannot be achieved, then a 
cavity filter is required (see § 1.8.3.2 and §1.8.3.3). Contact KERLINK for more information. 
 

3.4.2

 

Wirnet iBTS 915 

Co-localization is possible with the following BTS: 

-

 

GSM850, GSM1800, GSM1900 

-

 

UMTS850, UMTS1900, UMTS1700, UMTS2100 

-

 

LTE700, LTE850, LTE1700, LTE 1800, LTE1900, LTE2600 

 
Co-localization is not possible with (E)GSM900, UMTS900 and LTE900. 
In case of co-localization with GSM900, UMTS900 or LTE900, then the Wirnet iBTS 923 is a 
more suitable gateway. If Wirnet iBTS 915 want to be used when co-localized with GSM900, 
UMTS900  or  LTE900,  then  a  specific  cavity  filter  is  required.  Contact  KERLINK  for  more 
information. 

 
Note: 

In  Philippines,  co-localization  with  EGSM900  requires  usage  of  a  specific  cavity  filter  (see 
§1.8.3.4). Contact KERLINK for more information. 
 

3.4.3

 

Wirnet iBTS Full-Duplex 

Co-localization is possible with the following BTS: 

-

 

GSM850, GSM1800, GSM1900 

-

 

UMTS850, UMTS1900, UMTS1700, UMTS2100 

-

 

LTE700, LTE850, LTE1700, LTE 1800, LTE1900, LTE2600 

Co-localization is not possible with (E)GSM900, UMTS900 and LTE900. 
 

3.4.4

 

Wirnet iBTS 923 

Co-localization is possible with the following BTS: 

-

 

GSM850, GSM900, GSM1800, GSM1900 

-

 

UMTS850, UMTS900, UMTS2100 

-

 

LTE700, LTE800, LTE850, LTE 900, LTE 1800, LTE 2100, LTE 2300, LTE2500, LTE2600 

 
Co-localization is not possible with EGSM900, only GSM900. 
 

Note 1: 

In  Singapore,  Indonesia  and  Hong-Kong,  co-localization  with  EGSM900  requires  usage  of  a 
specific cavity filter. See §1.8.3.6. Contact KERLINK for more information. 
 

Содержание 1LOC868-1W868-EU






























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды