Kerlink 1LOC868-1W868-EU Скачать руководство пользователя страница 117

Страница: 117 / 221

Wirnet iBTS

Document title : Installation and
Maintenance Manual
Version : 2.0
Author : SNI
Date : 04/12/2018

Classification

This document is the strict property of Kerlink and shall not be either copied nor sent without express

written authorization of Kerlink

Internal Use

Kerlink m2m technologies reserved rights

Confidential

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

Page 117 / 221

Strict confidential

Figure 79 : Universal antenna bracket dimensions

The universal antenna bracket has 3 holes dedicated to the LoRa antenna N connector. The
bracket can be then oriented in 3 different positions without compromising the antenna
position.
The universal antenna bracket can be mounted:

On a wall: use in this case two M4 screws separated by 19mm.

On a pole: use metallic strapping through the two 5mm x 25mm slots.

On the compact casing mounting kit, with 2 x M8 bolts and screws.

1.8.6.3

Dome antenna bracket

The dome antenna bracket is used for the following antennas:

GNSS antenna (see §1.8.2.1)

LTE antenna (see §1.8.2.2)

GNSS/LTE combo antenna (see §1.8.2.3)

The dome antenna bracket is presented hereafter:

Slots for metallic
strapping

Fixing holes
(wall mount)

Holes for antenna

Содержание 1LOC868-1W868-EU






























































































































































































































Результаты поиска

Содержание 1LOC868-1W868-EU

Отзывы:

Бренды по названию

Популярные бренды

Kerlink 1LOC868-1W868-EU, Руководство по установке и обслуживанию

Результаты поиска

Содержание 1LOC868-1W868-EU

Отзывы:

Бренды по названию

Популярные бренды