Kenwood TK-2170 SERIES Скачать руководство пользователя | Manualshive

Страница: 88 / 142

background image

76

Confidential

FUNC (K)/Ver. 1.01

19 2-TONE

This transceiver supports 2-tone signaling.
2-tone signaling uses a pair of 2 different continuous tone
frequencies. 2-tone signaling is used to make an
individual call in Conventional Group.
2-tone signaling uses 2 different sequential tones. The
frequency range is from 288.5 to 3106.0 Hz. Sometimes,
only single tone is used.

Note:

2-tone is available only in Conventional Group.

19.1 Transmitting 2-tone

An Encode Tone configured for the Encode Memory List
can be selected by pressing the

2-tone

key. Select the

tone to transmit and press the

PTT

switch to transmit the

tone.

Transceiver Operation

1.

Press the

2-tone

key.

The smallest Autodial list number appears on the
display immediately after the transceiver is turned
ON. Otherwise, the previous list number appears.

2.

Select the 2-tone Encode List to send.
•

Using the

PF

keys

Press the

[<B]

or

[C>]

key.

•

Using the

Selector

*1

Turn the

Selector

.

*1

If the List Selection Key (Selector) is enabled.

3.

Press the

PTT

switch to send the 2-tone Encode

Tone and voice.
Press the

Side 2

key to transmit only the 2-tone

Encode Tone.

19.2 Encode

The following functions relevant to 2-tone Encode can be
configured by using KPG-101D:
•

Duration of 1st Tone

•

Duration of 2nd Tone

•

Duration of Single Tone

•

Gap Time

•

First Tone Delay Time

•

Sidetone

•

2-tone Encode Memory List

19.2.1 Duration of 1st Tone

The Duration of 1st Tone can be used to configure the 1st
Tone Encode duration for transmitting the 2-tone
configured for the 2-tone Encode Memory List.
The Duration of 1st Tone can be configured by using
KPG-101D. Normally, the Duration of 1st Tone is
configured for 1 second.

Configuration using KPG-101D

•

Configuring the Duration of 1st Tone (Refer to
FPRG 6.11.1 Encode Tab - Duration of 1st Tone.)

«
...
86
87
88
89
90
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов

Похожие инструкции для TK-2170 SERIES

Бренд: M/A-Com Страницы: 44

Бренд: M/A-Com Страницы: 72

Бренд: Simons Voss Technologies Страницы: 116

Бренд: Powermate Страницы: 12

Бренд: perfect pro Страницы: 177

Бренд: Sungale Страницы: 24

Бренд: ISKCO Страницы: 4

Бренд: Saluki Страницы: 42

Бренд: Magnum Страницы: 52

615 - DVP 615 - DVD Player

Бренд: Zenith Страницы: 40

Бренд: Sylvania Страницы: 24

Бренд: Hytera Страницы: 9

Бренд: Briggs & Stratton Страницы: 156

Бренд: Mercedes-Benz Страницы: 23

Бренд: Uniden Страницы: 84

Бренд: BRONDI Страницы: 7

Бренд: Vertex Standard Страницы: 116

Бренд: Sony Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды