Kenwood TK-2170 SERIES Скачать руководство пользователя | Manualshive

Страница: 54 / 142

background image

14 CONVENTIONAL GROUP

42

Confidential

FUNC (K)/Ver. 1.01

14.2.7 Transmit Power

Transmit Power is the transmission power of the
transceiver. Low can be configured for the transmit
power to reduce battery consumption if a repeater or the
receiving party is nearby.
Therefore, the operating time of the transceiver is also
extended.
Transmit Power can be switched between High and Low
by pressing the

Low Transmit Power

key.

Transmit Power can be configured by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the Transmit Power (Refer to FPRG
6.4.9 Transmit Power.)

•

Assigning functions to the

PF

keys (Refer to

FPRG 6.8 Key Assignment.)

14.2.8 Wide/ Narrow

Select the Channel Spacing for available channels.
Wide/ Narrow can be configured by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Wide/ Narrow (Refer to FPRG
6.4.10 Wide/ Narrow.)

14.2.9 Optional Signaling

Optional Signaling is signaling used for making an
individual call.

(Refer to 16.2 Optional Signaling on page

Optional Signaling can be configured for each channel by
using the KPG-101D.

Configuration using KPG-101D

•

Configuring the Optional Signaling (Conventional
Group) (Refer to FPRG 6.4.11 Optional
Signaling.)

14.2.10 Busy Channel Lockout

If a user transmits on a channel while other groups are
using that channel, the user may interfere with the other
groups’ communications. Busy Channel Lockout
prevents such interference.

(Refer to 10 Busy Channel

Lockout on page 33.)

Busy Channel Lockout can be configured for each
channel by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Busy Channel Lockout (Refer to
FPRG 6.4.12 Busy Channel Lockout.)

14.2.11 PTT ID

PTT ID is the transceiver identification code sent when
the

PTT

switch is pressed and/or released.

PTT ID on page 36.)

The timing to send the PTT ID can be configured by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the PTT ID (Refer to FPRG 6.4.13
PTT ID.)

14.2.12 PTT ID (BOT)

PTT ID (BOT) is the ID Code sent at the beginning of the
transmission when the transceiver sends the PTT ID
while DTMF is configured for PTT ID Type.
PTT ID (BOT) can be configured by using KPG-101D.
(Refer to FPRG 6.4.14 PTT ID (BOT).)

14.2.13 PTT ID (EOT)

PTT ID (EOT) is the ID Code sent at the end of the
transmission when the transceiver sends the PTT ID
while DTMF is configured for PTT ID Type.
PTT ID (EOT) can be configured by using KPG-101D.
(Refer to FPRG 6.4.15 PTT ID (EOT).)

«
...
52
53
54
55
56
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов

Похожие инструкции для TK-2170 SERIES

Бренд: MagicBox Страницы: 20

Бренд: Vapor Страницы: 114

Nite Lite V Series

Бренд: Allmand Страницы: 17

Бренд: Extron electronics Страницы: 32

Бренд: Radio Shack Страницы: 45

TPA-2171 bluerock

Бренд: texet Страницы: 10

Бренд: Denver Страницы: 11

Бренд: auna Страницы: 152

Бренд: GE Страницы: 88

Бренд: Lenox Страницы: 17

Бренд: RCA Страницы: 15

Бренд: Titan Страницы: 24

Бренд: Firman Страницы: 41

Бренд: Firman Страницы: 42

Бренд: Firman Страницы: 111

ExtendAir eMIMO r5050 Series

Бренд: Exalt Страницы: 12

Бренд: Curtis Страницы: 1

Бренд: Curtis Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды