Kenwood NX-5000 series Скачать руководство пользователя страница 88

Страница: 88 / 264

Note

Alert Tone (Text Message Call)

is configured to sound when receiving, an Alert Tone sounds.

To receive a text message, the received NAC needs to match.

The transceiver can send and receive a text message even if

Optional Signaling

is configured. (Refer to

Using the

Optional Signaling (P25)

As for the

Auto Reset Timer

, the

Auto Reset Timer

for text messages is used. (Refer to

Auto Reset Timer

Configuration using KPG-D1/ D1N

Configuring

Alert Tone (Text Message Call)

(

Transceiver Settings > P25 > P25 Information > Conventional > Alert

Tone)

Text Message Stack

is the function to store a text message in the stack memory. A maximum of 128 text messages can

be stored in the stack memory.

If a message is stored in the transceiver, the transceiver blinks the “

” icon for notification. In this case, a user can read

the stored text message when the transceiver enters Stack Mode. (Refer to Common FUNC

Viewing the Receive History

(Stack)

Note

The maximum number of text message data that can be stored in the transceiver stack memory varies as follows
depending on the configuration of

Short Message Stack

in each communication protocol.

Table 1-18 No. of Short Message Data That can be Stored

Short Message Stack or Text Message Stack Configuration

The maximum number of

data that can be stored

FleetSync

NXDN

P25

DMR

Disabled

Enabled

Disabled

128

Disabled

Enabled

Disabled

128

Enabled

Disabled

128

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Configuration using KPG-D1/ D1N

Configuring

Text Message Stack

(

Transceiver Settings > P25 > P25 Information > General > Stack)

1 P25 CONVENTIONAL SYSTEM

1.14 Sending and Receiving a Text Message (Text Messaging)

P25 FUNC (K)/Ver 2.20

CONTENTS

INDEX

Содержание NX-5000 series









































































































































































































































































Результаты поиска

Содержание NX-5000 series

Отзывы:

Бренды по названию

Популярные бренды

Kenwood NX-5000 series, Руководство пользователя

Результаты поиска

Содержание NX-5000 series

Отзывы:

Бренды по названию

Популярные бренды