manualshive.com logo in svg

Kenwood NX-5000 series, Руководство пользователя

Поделиться
Скачать
Kenwood NX-5000 series Скачать руководство пользователя страница 72

Note

The transceiver enters the Radio Inhibit state when the transceiver receives a Radio Inhibit request message even if the
transceiver receives DTMF or FleetSync signaling and enters the Stun state. If the transceiver in this state receives a
command to reset the Stun state, the Stun state is reset, but the Radio Inhibit state is not reset.

Configuration using KPG-D1/ D1N

Configuring 

Radio Inhibit

 to be enabled or disabled (

 Transceiver Settings > Personal > Personal Features > P25

Conventional (P25 Voting with NAC) > P25)

Transceiver Behavior upon Receipt of the Radio Uninhibit Request Command

If the transceiver receives a Radio Uninhibit request message while in the Radio Inhibit state, the transceiver sends an ACK
to the system that sent the Radio Uninhibit request message. Then, the Radio Inhibit state is reset and the transceiver can
be used again.
However, the Radio Inhibit state is not reset if the Target ID for the Radio Inhibit request message is configured for other
than own. Also, the transceiver does not send any ACK.
To receive a Radio Uninhibit request message and accept the received message, 

Radio Inhibit

 needs to be enabled.

Note

Only if all of the following conditions are satisfied, the password entry screen appears upon reset of the Radio Inhibit state:

0

A Transceiver Password is configured for the transceiver.

0

“Transceiver Password” is not assigned to a key of the transceiver.

0

The transceiver has been turned OFF to ON when the transceiver is in the Radio Inhibit state.

Configuration using KPG-D1/ D1N

Configuring 

Radio Inhibit

 to be enabled or disabled (

 Transceiver Settings > Personal > Personal Features > P25

Conventional (P25 Voting with NAC) > P25)

Transceiver Behavior in the Radio Inhibit State

The transceiver in the Radio Inhibit state appears to be in the same state as if the transceiver is turned OFF.
The following is the transceiver behavior while the transceiver is placed in the Radio Inhibit state:

0

The LCD, LED, and Backlight are all turned Off.

0

The speaker is muted.

0

Operations other than turning the transceiver OFF cannot be done.

0

Communications using commands other than the following commands are ignored:

0

Radio Check

0

Radio Inhibit/ Radio Uninhibit

0

The control commands specified by the PC Interface Protocol are not accepted. In this case, neither an ACK nor a NACK
is returned.

0

PC commands, such as the J Command, are not sent even if the transceiver status changes.

0

The AUX Input functions do not function. (Mobile only)

0

However, the following AUX Output functions are disabled: (Mobile only)

0

LOK

0

COR

0

TOR

0

PTT Output

0

TXS

1 P25 CONVENTIONAL SYSTEM

1.11 Disabling the Transceiver Capability by Remote Control (Radio Inhibit / Uninhibit)

P25 FUNC (K)/Ver 2.20

52

CONTENTS

INDEX

Содержание NX-5000 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды