background image

English

-

5

Installation of the GPS Antenna

• GPS antenna 

D

can be installed either inside or outside of the car, but either way it should be

installed as horizontally as possible to allow easy reception of the GPS satellite signals.

• The reception conditions of the GPS satellite will be less favorable with installation inside the car

as compared to outside the car. Depending on the type of car, reception of the GPS satellite signals
might not be possible with an inside installation. Installation outside of the car is recommended if
circumstances allow.

• The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from

cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with
by these types of communication.

• Do not remove the tape from the back of the GPS antenna. When the tape comes off, the

waterproof effectiveness is diminished and this may cause a fault in the GPS antenna.

• Painting the GPS antenna with (metallic) paint may cause a drop in performance.

2

CAUTION

Installation Outside the Car

Installation to the trunk lid is made with the GPS
antenna 

D

built-in magnet.

1

Affix the waterproof pad that accompanies 

E

at the

place that comes up against the waterproof rubber
lining the trunk.

2

Draw the cable of 

D

from the trunk lid into the trunk.

Installation Inside the Car

Install at a place close to the window surface at the
center of the rear tray or on the inside of the rear
window to allow easy reception of the GPS satellite
signals.

1

Peel off the release paper of 

F

and affix to

placement position of 

D

.

2

Place 

D

on 

F

.

D

E

D

F

KNA-DV3100Inst(K)_En  03.5.8  10:06 AM  Page 5

Содержание KNA-DV3100









Отзывы: