32
English
English
33
Installation/connection
Part list:
A
Faceplate ...................................................................(×1)
B
Escutcheon ..............................................................(×1)
C
Mounting sleeve ...................................................(×1)
D
Wiring harness .......................................................(×1)
E
Removal tool .......................................................... (×2)
F
Microphone (3 m) ................................................(×1)
Basic procedure
1
Remove the key from the ignition switch,
then disconnect the
·
terminal of the
car battery.
2
Make proper input and output wire
connections.
\
3
Install the unit to your car.
\
<Installing the unit> (page 35)
4
Reconnect the
·
terminal of the car
battery.
5
Reset the unit. (
)
¤
Warning
■
■
The unit can only be installed in a car with a
12 V DC power supply, negative ground.
■
■
If you connect the ignition wire (red) and
the battery wire (yellow) to the car chassis
(ground), you may cause a short circuit,
that in turn may start a fire. Always connect
those wires to the power source running
through the fuse box.
■
■
Disconnect the battery’s negative terminal
and make all electrical connections before
installing the unit.
■
■
Insulate unconnected wires with vinyl tape
or other similar material. To prevent a short
circuit, do not remove the caps on the ends
of the unconnected wires or the terminals.
■
■
Be sure to ground this unit to the car’s
chassis again after mounting.
■
■
If the power is not turned ON (“PROTECT”
is displayed), the speaker wire may have a
short-circuit or touched the chassis of the
vehicle and the protection function may
have been activated. Therefore, the speaker
wire should be checked.
¤
Caution
■
■
If your car’s ignition key switch does not
have an ACC position, connect the ignition
wires to a power source that can be turned
on and off with the ignition key. If you
connect the ignition wires to a constant-
voltage power source, as with battery wires,
the battery may die.
■
■
Do not use your own screws. Use only the
screws provided.
■
■
Install this unit in the console of your
vehicle. Make sure the faceplate will not hit
the lid of the console (if any) when closing
and opening.
■
■
After the installing the unit, check whether
the brake lamps, blinkers, wipers, etc. on the
car are working properly.
■
■
Mount the unit so that the mounting angle
is 30° or less.
■
■
If the fuse blows, first make sure the wires
are not touching other parts to cause a
short circuit, and then replace the old fuse
with one with a new the same rating.
■
■
Connect the speaker wires correctly to the
corresponding terminals. The unit may be
damaged or fail to work if you share the
·
wires or ground them to any metal part in
the car.
■
■
When only two speakers are being
connected to the system, connect the
connectors either to both the front output
terminals or to both the rear output
terminals (do not mix front and rear).
■
■
Mounting and wiring this product requires
skills and experience. For safety’s sake, leave
this work to professionals.
If you experience problems during
installation, consult your Kenwood dealer.
■
■
Reception may become poor if there are
metal objects near the Bluetooth antenna.
Bluetooth antenna unit
PAR
iPod
VOICE
For Good Reception
To assure good reception, note the following:
■
■
Communicate with the cell-phone within
the line-of-sight distance of 10 m (30
ft). The communication range becomes
shorter depending on the surrounding
environment. The communication
range also becomes shorter when there
is an obstacle between this unit and
the cell-phone. The above maximum
communication range (10 m) is not always
assured.
■
■
A broadcast station or walkie-talkie located
nearby can interfere with communication
due to a too strong signal.
¤
CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
