background image

18

DETERGENT AND DISPENSER USE

A Word About Detergents

High-Efficiency (HE) detergents produce fewer suds, 

dissolve more efficiently to improve washing and rinsing 

performance, and help to keep the interior of your 

washer clean. Using detergent that is not HE may cause 

oversudsing and unsatisfactory performance which 

could result in error codes, cycle failure, and 

 

machine damage.

For proper wash performance, always measure the

detergent using the measurements provided by the 

detergent manufacturer.

The normal amount of HE detergent needed, for average 

loads, is less than ½ of the recommended maximum. 

Use less detergent

 for soft water, light soil or smaller 

loads. 

Never

 use more than the maximum amount 

recommended by the detergent manufacturer.

IMPORTANT: 

Not all detergents are the same. Pay 

careful attention to the amount of detergent used to avoid 

overusing, poor rinsing and detergent buildup in clothing, 

and residue buildup that can contribute to odors in the 

machine. NEVER use a cup or scoop other than the one 

supplied by the manufacturer of the detergent you 

are using. Never use more than the maximum amount of 

detergent recommended by the manufacturer.
Always measure the detergent amount. While HE 

detergents are designed for this type of washing 

machine, be careful when measuring the detergent. For 

most normal loads, no more than 

1/4 to 

½  of cap or 

scoop of HE detergent should be used.

NOTE:

 Extra care must be exercised when using 

2X

 and 

3X 

concentrated detergents because even a little bit extra 

can contribute to the problems mentioned above.

NOTE:

 Detergents designated as HE compatible may not

provide optimal results.

IMPORTANT:

 Your washing machine is designed for use

with only High-Efficiency (HE) detergents. HE detergents 

are formulated specifically for High-Efficiency washers 

and contain suds-reducing agents. Always look for the 

HE symbol when purchasing detergent.

Designed to use only

High-Efficiency (HE) detergent

Using the Softener and Detergent Dispenser

To add detergent, bleach, and fabric softener to the

automatic dispenser:

       

Open the dispenser drawer.

       

Load the laundry products into the 

 

       appropriate compartments.

       

Close the drawer before starting the cycle.

     

NOTE:

 It is normal for a small amount of water to 

remain in the bleach and softener compartments at the 

end of the cycle.

I

MPORTANT:

 Do not place or store laundry products, 

such as detergent, bleach, or liquid fabric softener, on top 

of your washer or dryer. Wipe up any spills immediately. 

These products can damage the finish and controls.

Using the Liquid Bleach Dispenser

The bleach dispenser automatically dilutes and 

dispenses liquid bleach at the proper time in the 

 

wash cycle.

Check clothing care labels for special instructions.

Measure liquid bleach carefully, following 

instructions on the bottle. High-efficiency washers 

use less water, so less bleach is needed. One half 

cup is enough for most loads.
Carefully pour the pre-measured amount of bleach 

directly into the bleach dispenser. If you are using 

powdered bleach of any kind, pour it directly into 

the tub before adding the laundry. Never add 

powdered bleach to the liquid bleach dispenser.

• Never pour undiluted liquid chlorine bleach directly onto 

clothes or into the tub.

• Do not pour powdered bleach into bleach dispenser. 

• Do not place laundry items on top of the bleach 

dispenser when loading and unloading the washer.

• Always measure and pour bleach carefully. Avoid 

overfilling or splashing when adding bleach to the 

dispenser. The maximum capacity of the bleach 

dispenser is one cup of bleach per wash cycle. 

Overfilling could result in bleach being dispensed 

immediately.

1

2

3

Maximum

Normal Load Amount

Liquid 

Detergent

Powdered 

Detergent

1

2

3

HOW TO USE

Содержание 796.3151#21 Series



































Отзывы: