background image

13

Drill a ¼” (6.35 mm) hole in the water
pipe (even if using a self-
piercing valve) using a
sharp bit. Remove any burrs
resulting from drilling the  
hole in the pipe. Take care
not to allow water to drain
into the drill. Failure to drill a ¼” (6.35 mm) hole 
may result in reduced ice production or smaller cubes. 

3. DRILL THE HOLE FOR THE VALVE

4. FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with
the pipe clamp.

NOTE:

Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.

5. TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer
begins to swell. 

NOTE:

Do not overtighten or you may crush 

the tubing.

6. ROUTE THE TUBING

Route the tubing between the cold water line and the
refrigerator.

Route the tubing through a hole drilled in the wall or
floor (behind the refrigerator or adjacent base 
cabinet) as close to the wall as possible. 

NOTE:

Be sure there is sufficient extra tubing [about

8 feet (244 mm) coiled into 3 turns of about 10” 
(25 cm) diameter] to allow the refrigerator to move 
out from the wall after installation.

Vertical Cold
Water Pipe

Saddle-Type
Shutoff Valve

Pipe Clamp

Washer

Inlet End

Pipe Clamp

Clamp Screw

7. CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) 
for copper tubing onto the end of the tubing and
connect it to the shutoff valve. Make sure the tubing 
is fully inserted into the valve. Tighten the 
compression nut securely.

.

NOTE:

Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.

Saddle-Type
Shutoff Valve

Packing
Nut

Outlet
Valve

Ferrule (sleeve)

Compression
Nut

1. SHUTOFF THE MAIN WATER SUPPLY

Turn on the nearest faucet to relieve the pressure on 
the line.

Choose a location for the valve that
is easily accessible. It is best to connect
into the side of a vertical water pipe.
When it is necessary to connect into a
horizontal water pipe, make the
connection to the top or side, eather
than at the bottom, to avoid drawing
off any sediment from the water pipe.

2. CHOOSE THE VALVE LOCATION

INSTALLATION INSTRUCTIONS

Install the shutoff valve on the nearest frequently used 
drinking water line.

REFRIGERATOR INSTALLATION

NOTE:

 Licensed plumbers must use only cooper tubing

            NDA tubing #49595 or 49499 or Cross Link 
            Polyethylene (PEX) tubing.

Содержание 795.5131 Series


































Отзывы: