17
■
Turn the T
URBO
Z
ONE
™ wash option off if not loading items
for this option. Always use the Heavy Soil detergent fill
recommendation with T
URBO
Z
ONE
™ wash option. (See
“How much detergent to use” in “Detergent Dispenser”
section.)
Hi Temp
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp wash raises the water
temperature to 145ºF (63ºC), in the main wash. Heating the water
helps improve washing results. Hi Temp wash is useful when
loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE:
Hi Temp wash is an option with the SMART WASH™,
Pots Pans, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE:
Sani Rinse is an option with SMART WASH™, Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSI requirements.
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dishload that will not be dry at the end of the cycle.
NOTE:
The Heated Dry option is used in all cycles except Fast
Wash and Quick Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher
between cycles.
When Lock On is lit, all buttons are disabled.
NOTE:
The dishwasher door can be opened while the controls
are locked.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. Lock On glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE:
If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours/4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, press START/RESUME. Make sure the
door is latched or the delay will not continue.
To delay the start
1.
Press the delay button to choose the number of hours
delayed.
2.
Select a wash cycle and options.
3.
Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
■
To cancel the delay and cycle, press CANCEL/DRAIN.
■
To cancel the delay and start the cycle, press START/
RESUME.
■
On top control models, if the door is not closed within
3 seconds of pressing Start/Resume, press START/RESUME
again.
Cycle Status Indicators
Follow the progress of your dishwasher with the Cycle Status
indicators.
NOTE:
The features on your dishwasher may vary from those
shown here.
Clean
Clean glows when a cycle is finished. The light turns off when you
press any button or close the door.
Sanitized
If you select the Sani Rinse option, Sanitized glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted or the incoming water
temperature is too low. The light turns off when you press any
button or close the door.
Side view of T
URBO
Z
ONE
™ wash area
