Kenmore 111.6914 Series страница 14 Скачать руководство пользователя

Страница: 14 / 31

LEVELING THE DRYER

WARNING:

• To reduce the risk of injury to persons, adhere

to all industry recommended safety procedures

including the use of long sleeved gloves and

safety glasses. Failure to follow this warning can

cause serious injury or death.

• The appliances are heavy. Two or more people

are required when installing the dryer. Failure to

follow this warning can cause serious injury or

death.

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize vibration,

noise, and unwanted movement, the floor must be a level,

solid surface.

NOTE:

Adjust the leveling feet only as far as necessary

to level the dryer. Extending the leveling feet too far can

cause the dryer to vibrate.

Position the dryer in the final location. Place a level

across the top of the dryer.

Level

Leveling Feet

Once feet are adjusted (see step 2 below), gently push

on the top corners of the dryer to make sure that the

dryer does not rock from corner to corner.

Turn each leveling foot clockwise to raise that corner

of the dryer. Turn foot counterclockwise to lower. Keep

checking the leveling tool as you adjust feet until the

dryer is level from side to side and front to back.

REVERSING THE DOOR SWING

Tools Required

•

Phillips or large flat-blade screwdriver (for hinge screws)

•

Small flat blade screwdriver

(for lifting out parts)

WARNING:

• THE DRYER DOOR IS VERY LARGE AND HEAVY.

Failure to follow the instructions below can result

in damage to the dryer, property damage or

personal injury.

• To avoid damage to the dryer or the door, support

the door with a stool or box that fits under the

door, or have an assistant support the weight of

the door.

• Avoid dropping the door to avoid damage to the

door or the floor.

• Unplug the dryer or turn off power at the main

circuit breaker before beginning door reversal.

Door Reversal Instructions

NOTE:

The following instructions are for changing the

door swing from a right to a left side hinge. If the door

has been reversed, and it is necessary to change it back,

use care when following these instructions. Some of the

illustrations and the left/right references will be reversed,

and you will need to read the instructions carefully.

IMPORTANT

If after reading the following instructions you are not

confident that you can successfully complete the door

reversal, contact a qualified service technician to perform

the procedure.

Open the door from the side so that the hinge screws

are accessible.

WARNING:

Be sure to support the weight of the door before

removing the hinge screws

Remove the 4 hinge screws.

1. Place a soft rug on the floor to rest the door on after it

has been removed to prevent it from being scratched.

2. Unplug the dryer power cord from the electrical

outlet.

3. Remove the four hinge screws from the door, two

from each hinge. Then remove the door by lifting it

up slightly.

INSTALLATION INSTRUCTIONS

Kenmore(북미향 건조기) 111.6914#(EN).indd 14

2021-06-09 오전 10:35:35

Содержание 111.6914 Series
































Результаты поиска

Содержание 111.6914 Series

Отзывы:

Похожие инструкции для 111.6914 Series

Бренды по названию

Популярные бренды

Kenmore 111.6914 Series, Инструкция по использованию и уходу

Результаты поиска

Содержание 111.6914 Series

Отзывы:

Похожие инструкции для 111.6914 Series

Бренды по названию

Популярные бренды