Kemppi SuperSnake GTX Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 35

Kemppi SuperSnake GTX Скачать руководство пользователя страница 3

SuperSnake GTX

Operating manual - EN

1. GENERAL

Kemppi SuperSnake GTX is a subfeeder device designed for professional use in MIG/MAG welding. When used together
with the protective frame, SuperSnake GTX is especially robust and durable in hard-to-reach welding conditions.

SuperSnake GTX compatible equipment:

•

X5 FastMig with X5 Wire Feeder 300 Auto+ wire feeder

•

Other X5 FastMig wire feeder equipment with dedicated subfeeder installation kit (contact your Kemppi dealer for
more information on compatibility).

Important notes

Read the instructions through carefully. For your own safety, and that of your working environment, pay particular atten-
tion to the safety instructions delivered with the equipment.

Items in the manual that require particular attention in order to minimize damage and harm are indicated with the
below symbols. Read these sections carefully and follow their instructions.

Note: Gives the user a useful piece of information.

Caution: Describes a situation that may result in damage to the equipment or system.

Warning: Describes a potentially dangerous situation. If not avoided, it will result in personal damage or fatal injury.

Kemppi symbols:

DISCLAIMER

While every effort has been made to ensure that the information contained in this guide is accurate and com-
plete, no liability can be accepted for any errors or omissions. Kemppi reserves the right to change the spe-
cification of the product described at any time without prior notice. Do not copy, record, reproduce or transmit
the contents of this guide without prior permission from Kemppi.

© Kemppi

3

1921930 / 2144

«
1
2
3
4
5
...
»

Содержание SuperSnake GTX




































Отзывы:

Нет отзывов