Kemppi Promig 530 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

Kemppi Promig 530 Скачать руководство пользователя страница 17

Promig 530 / 061 – 1

© kemPPi oy

SELECTO operations

SELECTO mode switch S24
OFF:  Normal MIG/MAG welding
ON:  Welding with memory stored values (5 channels)
SET:  Welding parameters selection and storage SAVE (S25), for selected channel CH 1...5

(S26).

Welding method selecting switch S21

MMA: MMA welding with stepless welding current control
MIG two-sequence procedure
MIG/MAG welding with two-sequence procedure of welding gun start switch
1. switch pressed: welding starts
2. switch open: welding stops
MIG four-sequence procedure
MIG/MAG welding with four-sequence procedure of welding gun start switch
1. switch pressed: shielding gas flow starts
2. switch open: welding starts
3. switch pressed: welding stops
4. switch open: shielding gas flow stops

Control mode selecting switch S22

Local control:
Control potentiometers R21 and R22 on panel are used.
Remote control:
Adjustments are carried out from remote control unit R20 which is connected to

remote control connector X11 of wire feed unit.

If you use the remote control unit R10, adjust wire feed speed or MMA welding current with

potentiometer of the R10 and voltage with potentiometer U on panel.
Gun control:
Wire feed speed is adjusted with control module RMT 10 which is connected to KEMPPI PMT or

WS welding gun and welding voltage is adjusted with potentiometer.
Note! If the remote control unit or the gun control unit is not connected to the PROMIG and you

have selected remote control or gun control, then controls operate with local controlpotentiometers

like in local control position.

Local controls R21, R22

potentiometer

SELECTO OFF: Local control for wire feed speed 0...18 m/min

or 0...25 m/min

SELECTO ON: No operation

SELECTO SET: Local control for wire feed speed 0...18 m/min

or 0...25 m/min

MMA welding: Welding current control, 10 A...max. current of

power source

potentiometer

SELECTO OFF: local control for voltage of PRO power source,

10 V...max. MIG voltage of power source

SELECTO ON: No operation

SELECTO SET: local control for voltage of PRO power source,

10 V...max. MIG voltage of power source

MMA welding: No operation

«
...
15
16
17
18
19
...
»

Содержание Promig 530





































Отзывы:

Нет отзывов