Kellfri 35-FDM160 Скачать руководство пользователя страница 5

Страница: 5 / 56

Table of Contents >>

SURROUNDINGS

Check that the work area is free from bystanders and objects before hitching or using the equip-

ment. Otherwise, there is a risk of serious injury. Be extra careful if there are children in the vicinity

of the area where the equipment or product is used or stored. Check that there are no low-hanging

electrical cables within the work area. Exercise caution when working on slopes and close to ditches.

Always work alone with equipment or products that are made for working alone. Never leave

rubbish in the work area, and keep work surfaces clean. Always respect the equipment's risk zone.

BEFORE USE

Carefully read the safety instructions and the operating manual. Make sure that you understand

the safety instructions, the operating manual and warning decals. Use common sense and

suitable personal protective equipment when using the product. Always check the performance

of the machine combination to be used. It is important that these are compatible and work

satisfactorily together. This is to ensure that the equipment or product works as expected, and

to guarantee the safety of yourself and others. Carry out a visual inspection of the equipment or

product before use. Repair or replace damaged or worn parts to reduce the risk of injury. Grease

moving parts and check that all nuts and bolts are tightened. Repair if necessary. Learn and

remember the correct working method. Beginners must work slowly until they have learned how

the machine or product works.

Users/customers are responsible for ensuring users can handle the situation. If a user feels that the

machine is dangerous to use, they should not use it until they have received thorough training.

WARNING!

Never use equipment or products with defective safety components.

Children must not be left unsupervised in the area!

Warning!

ENVIRONMENT

•

Disposal of oil and other waste

•

Improper disposal of oil or other waste may be hazardous to the

environment.

•

When oil is emptied from the machine, it must be poured into

a leak-proof container suitable for oil. It is not permissible to store oil

in a container used for food or drink, in order to avoid the oil being

consumed by mistake and causing serious injury.

•

It is prohibited to spill oil on the ground, or pour it into a drain

or anywhere leading to a water source.

•

Discarded oil, fuel, coolant, brake fluid, filters and batteries must not

be thrown away or emptied in just any manner. Contact your local

authority for further information.

Содержание 35-FDM160

























































Результаты поиска

Содержание 35-FDM160

Отзывы:

Похожие инструкции для 35-FDM160

Бренды по названию

Популярные бренды

Kellfri 35-FDM160, Руководство пользователя

Результаты поиска

Содержание 35-FDM160

Отзывы:

Похожие инструкции для 35-FDM160

Бренды по названию

Популярные бренды