manualshive.com logo in svg

Kellfri 26-GAATV, Руководство пользователя, Страница: 12 / 28

Поделиться
Скачать
Kellfri 26-GAATV Скачать руководство пользователя страница 12

Table of contents

12

DIGGING MODE

After towing the backhoe to the desired location, follow these set-up instructions. Do not sit 

on the backhoe while setting it up.

1.  Remove outriggers from the attachment and set them aside. This reduces weight. Outrig-

gers are heavy, use lifting device when lifting.

2.  Be sure to remove the up-down and side-to side travel pins. Keep these two pins to re-in-

sert for towing.

UP-DOWN
TRAVEL PIN

SIDE-SIDE 
TRAVEL PIN

Disconnect the backhoe from the towing vehicle

3.  Pull lever #2 towards left until wheels elevate off the ground 4-5 inches.

4.  Remove wheels. Looking at until as if you were sitting is operator seat, put outrigger in 

front left slot,secure with pin and put front wheel by rear right slot. Install other outrigger 

in front right slot, secure with pin and put front right wheel by rear left slot. Lower wheels 

by pushing lever #2 right.

5.  Position bucket next to the right side outrigger. Elevate the right side of the unit by pull-

ing lever #2 left until right side balances enough to install back-right wheel into slot. The 

right outrigger should be about 2feet of the ground .Install back right wheel into slot and 

secure with pin.

6) Lower right side of until by pushing lever #2 right to where the outrig-

ger is touching the ground and the flat part of the bucket is flush to the 

ground .Insert the back-left wheel into the slot and secure with pin. If 

needed, move bucket next to the left outrigger and elevate the left side 

to allow wheel to be inserted in to slot. Make sure all pins are secure. 

 

     

The backhoe is now in digging mode. Read the entire manual before attempting to operate the 

backhoe. Like any industrial tool, proper training and preparation are needed to safely and 

efficiently operate the backhoe.

Содержание 26-GAATV





























Отзывы:

Нет отзывов