background image

1

PA-913 Rev. A / 12-05

 

S46T Microwave Switch System

Relay Installation Guide

Keithley Instruments, Inc.

28775 Aurora Road
Cleveland, Ohio 44139
(440) 248-0400
www.keithley.com

Introduction

This guide contains information on S46T relay installation and system configuration that is necessary after 
installing new relays. To install a relay, refer to 

“Relay kits” on page 1

 for a description of the kits and then 

follow the applicable installation instructions.

WARNING:

The information in this section is only intended for qualified service 
personnel. Do not attempt to replace parts or otherwise service the 
equipment unless you are qualified to do so.

Relay kits

Table 1

 summarizes available relay kits and part numbers.

WARNING:

Use only the parts specified in 

Table 1

 of this guide when servicing the 

equipment. Use of improper parts may expose the operator to 
hazardous voltages that could result in personal injury or death.

Table 1
S46T relay kits

Relay kit 

model number

Description

Relay

location

Kit parts summary

(Quantity)

Keithley 

part number

Installation 

reference

S46T-SPDT-KIT

18GHz SPDT

1 to 8  SPDT un-terminated relay (1) 

S40-0154 

“SPDT relay 1–

8 installation” 

on page 3

SPDT spacer (1) 

S40-SE05-307 

Connecting cable (1) 

SYS46-311C 

S46T-SP4T-KIT

18GHz SP4T A to D  4-40 ×1/4 PPHSEM screws (2)  4-40X1/4PPHSEM 

“Relay A–D 

installation” on 

page 5

4-40 ×3/8 PFH screws (4)

4-40x3/8PFH

SP4T relay (1)

RL-282-2

Ribbon cable (1) 

CA-286-1 

Mounting plate (1)

S40-N410-312

S46T-SP6T-KIT

18GHz SP6T  A to D  4-40 ×1/4 PPHSEM screws (2)  4-40X1/4PPHSEM 

“Relay A–D 

installation” on 

page 5

4-40 ×3/8 PFH screws (4)

4-40x3/8PFH

SP6T un-terminated relay (1)

RL-282-1

Ribbon cable (1)

CA-286-1

Mounting plate (1)

S40-N410-312

S46T-SPDT-KIT-26

26.5GHz 

SPDT

1 to 8  SPDT un-terminated relay (1) 

RL-308

“SPDT relay 1–

8 installation” 

on page 3

SPDT spacer (1) 

S40-SE05-307 

Connecting cable (1) 

SYS46-311C

S46T-SP4T-KIT-26

26.5GHz 

SP4T

A to D  4-40 ×3/8 PFH screws (4)

4-40x3/8PFH

“Relay A–D 

installation” on 

page 5

SP4T un-terminated relay (1)

RL-312

Mounting plate (1)

S40-N410-312

Ribbon cable (1) 

S46-U100-350A

Содержание S46T-SPDT-KIT







Отзывы: