manualshive.com logo in svg

Keithley KPXI, Руководство пользователя, Страница: 68 / 97

Поделиться
Скачать
Keithley KPXI Скачать руководство пользователя страница 68

B-12

Return to 

Section Topics

KPXI-CON-900-01 Rev. A / January 2007

Appendix B: Award BIOS Setup Utility

KPXI System Controller User’s Manual

NOTE

The settings on the screen are for reference only. Your version may not be identical to 
this one.

OnChip IDE Device

Move the cursor to this field and press <Enter>. The following screen will appear.

Figure B-7

OnChip IDE device

NOTE

The settings on the screen are for reference only. Your version may not be identical to 
this one.

On-Chip Primary PCI IDE and On-Chip Secondary PCI IDE

These fields allow you to enable or disable the primary and secondary IDE controller. Select 
Disabled if you want to add a different hard drive controller.

IDE Primary and Secondary Master/Slave PIO

PIO means Programmed Input/Output. Rather than have the BIOS issue a series of commands to 
affect a transfer to or from the disk drive, PIO allows the BIOS to tell the controller what it wants 
and then let the controller and the CPU perform the complete task by them. Your system supports 
five modes, 0 (default) to 4, which primarily differ in timing. When Auto is selected, the BIOS will 
select the best available mode after checking your drive.

•

Auto:

 The BIOS will automatically set the system according to your hard disk drive’s timing.

•

Mode 0-4: 

You can select a mode that matches your hard disk drive

’

s timing.

CAUTION

Do not use the wrong setting or you will have drive errors.

IDE Primary and Secondary Master/Slave UDMA

These fields allow you to set the Ultra DMA in use. When Auto is selected, the BIOS will select the 
best available option after checking your hard drive or CD-ROM.

•

Auto: 

The BIOS will automatically detect the settings for you.

•

Disabled: 

The BIOS will not detect these categories.

Содержание KPXI


































































































Отзывы:

Нет отзывов