manualshive.com logo in svg

Keithley DAS-8 Series, Руководство пользователя, Страница: 101 / 145

Поделиться
Скачать
Keithley DAS-8 Series Скачать руководство пользователя страница 101

 

6-3

 

Troubleshooting Table

 

Table 6-1 lists general symptoms and possible solutions for problems with 
DAS-8 Series boards. If your board is not operating properly after using 
this information, refer to Technical Support on page 6-5 for instructions 
on getting technical support. 

 

Table 6-1.  Troubleshooting Information  

 

Symptom

Possible Cause

Possible Solution

 

Board does not 
respond

Base address is unacceptable. Make sure that the base address specified in the 

configuration file matches the setting of the 
base address switch block on the board. Make 
sure that no other system resource is using any 
of the eight memory locations starting at the 
specified base address. Reconfigure the base 
address, if necessary. Refer to 

 

Setting the Base 

Address

 

 on page 3-8 for instructions.

Interrupt level is 
unacceptable.

Make sure that the interrupt level specified in 
the configuration file matches the setting of 
jumper J1 on the board. Make sure that no other 
system resource is using the specified interrupt 
level. Reconfigure the interrupt level, if 
necessary. Refer to 

 

Setting the Interrupt Level

 

 

on page 3-13 for instructions.

The board configuration is 
unacceptable. 

Check the settings in the configuration file. 
Make sure that they match the settings of the 
switches and jumper on the board, where 
appropriate. 

The board is incorrectly 
aligned in the accessory slot.

Check installation.

The board is damaged.

Contact the Keithley Data Acquisition 
Applications Engineering Department; refer to 
T

 

echnical Support on page 6-5

 

.

Intermittent 
operation

Vibrations or loose 
connections exist.

Cushion source of vibration and tighten 
connections.

The board is overheating.

Check environmental and ambient temperature.

Electrical noise exists. 

Provide better shielding or reroute wiring.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание DAS-8 Series


















































































































































Отзывы:

Нет отзывов