Keithley 7012-C Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 93

Keithley 7012-C Скачать руководство пользователя страница 29

Card Connections & Installation

3-2

WARNING

The following connection informa-
tion is intended to be used by quali-
Þed service personnel. Failure to
recognize and observe standard safe-
ty precautions could result in person-
al injury or death.

3.3.1 Backplane row jumpers

The Model 7001 mainframe has an analog backplane
that allows the rows of a Model 7012 matrix to be inter-
nally connected to a compatible switching card in-
stalled in the other slot (see paragraph 2.4.1 for details).

The backplane row jumpers for the matrix card assem-
bly are located on the relay card as shown in Figure 3-
1. The card is shipped from the factory with the jump-
ers installed.

Jumper removal

Perform the following steps to remove backplane row
jumpers:

1. If mated together, separate the relay card from the

connector card by removing the mounting screw
and then pulling the two cards away from each
other. Remember to only handle the cards by the
edges and shields to avoid contamination.

2. Use Figure 3-1 to locate the jumper(s) that are to be

removed.

3. It is not necessary to physically remove the jump-

ers from the PC board. Using a pair of wire cutters,
cut one lead of each jumper.

Jumper installation

Referring to Figure 3-1 for jumper locations, perform
the following steps to install backplane row jumpers:

1. If mated together, separate the relay card from the

connector card by removing the mounting screw
and then pulling the two cards away from each
other. Remember to only handle the cards by the
edges and shields to avoid contamination.

2. Physically remove a cut jumper by unsoldering it

from the PC board.

3. Install a new #22 AWG jumper wire (Keithley P/N

J-15) and solder it to the PC board.

4. Remove the solder ßux from the PC board. The

cleaning procedure is explained in paragraph 5.2.

3.3.2 Screw terminal connector card

The screw terminal connector card is shown in Figure
3-2. Connections are made directly to the screw termi-
nals of the four terminal blocks. Each screw terminal
will accommodate #16-22 AWG wire.

Wiring procedure

Perform the following procedure to wire circuitry to
the screw terminal connector card:

WARNING

Make sure all power is off and any
stored energy in external circuitry is
discharged.

Figure 3-1
Backplane row jumpers

H

L

H

L

H

L

H
L

Row 1

Row 2

Row 3

Row 4

7012 Relay Card

Jumpers

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

«
...
27
28
29
30
31
...
»

Содержание 7012-C






























































































Отзывы:

Нет отзывов