manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

Front Panel Operation

4-42

The above arm count indicates that the scanner
will arm one time. An arm count of “0000” indi-
cates that infinite is selected.

2. To program for a different count (1 to 9999), use the

keypad to enter the count value.

3. With the desired count value displayed, press EN-

TER. The display will return to the SETUP ARM
CONTROL menu.

TRIGGER CONTROL 

 

Use this menu item to enable or

disable the source bypass. The source bypass is used to
bypass the arm spacing event on the first pass through
the scan. With the SETUP ARM CONTROL menu dis-
played, select this menu item by placing the cursor on
TRIGGER-CONTROL and pressing ENTER. The fol-
lowing menu will be displayed:

TRIGGER CONTROL 

SOURCE

ACCEPTOR

Source 

 

With this selection, the source bypass is en-

abled. The arm spacing event will be bypassed on the
first pass through the arm layer if EXTERNAL or TRIG
LINK arm spacing is selected. This will allow opera-
tion to proceed on into the scan layer without having to
wait for the programmed event.

Acceptor 

 

With this selection, the source bypass is dis-

abled.

4.8.4

Channel restrictions

The Model 7001 can be programmed for the following
channel restrictions: 

•

The user can enable the SINGLE CHAN (channel)
mode to prevent more than one channel from be-
ing closed at the same time. 

•

The user can define a list of RESTRICTED CHAN-
NELS. Channels in this list cannot be closed. 

Perform the following steps to display the CHANNEL
RESTRICTIONS menu:

1. Display the CONFIGURE SCAN menu (see para-

graph 4.8, General rule #1). 

2. Use the cursor keys (

 and 

) to place the cursor

on CHAN-RESTRICTIONS, and press ENTER to
access the following menu: 

CHANNEL RESTRICTIONS 

SINGLE-CHAN

RESTRICTED-CHANNELS

SINGLE-CHAN 

 

Use this menu item to enable or dis-

able the single channel mode. With the single channel
mode enabled (ON), only one channel can be closed.
Two or more channels cannot be closed at the same
time. 

Perform the following steps to enable or disable the
single channel mode: 

1. With the CHANNEL RESTRICTIONS menu dis-

played, place the cursor on SINGLE-CHAN and
press ENTER. The following message will be dis-
played: 

SINGLE CHANNEL MODE 

OFF

ON 

Cursor position indicates the current status of the
single channel mode. 

2. Place the cursor on the desired state (ON or OFF)

and press ENTER. The display will return to the
CHANNEL RESTRICTIONS menu. 

Operating Notes: 

1. For Single Channel, when more than one channel

is assigned to a channel list, only the lowest num-
bered channel in the lowest numbered slot will
close when CLOSE is pressed. For example, as-
sume the following channel list is defined: 

SELECT CHANNELS 2!1, 2!2, 1!5 
When CLOSE is pressed, Channel 1!5 will close. 

2. When the single channel mode is enabled, all

stored channel patterns are cleared. For example, if
closed Channels 1!1 and 1!2 are stored at memory
location #001 (M1), enabling single channel will
clear that memory location. 

3. The single channel mode cannot be enabled if two

or more channels are currently closed. 

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Dataprobe iBoot PoE-P General Description Manual preview
iBoot PoE-P
Бренд: Dataprobe Страницы: 31
IBM ThinkPad 600 Product Overview preview
ThinkPad 600
Бренд: IBM Страницы: 13
IBM Flex System EN2092 Quick Start Manual preview
Flex System EN2092
Бренд: IBM Страницы: 2
Daxten SCOUTCOMBO - Installation Manual preview
SCOUTCOMBO -
Бренд: Daxten Страницы: 7
H3C Mini Series Manual preview
Mini Series
Бренд: H3C Страницы: 17
Raritan MCCAT18 Specifications preview
MCCAT18
Бренд: Raritan Страницы: 4
4B M800 Elite Series Operation Manual preview
M800 Elite Series
Бренд: 4B Страницы: 12
D-Link DXS-3410 Series Hardware Installation Manual preview
DXS-3410 Series
Бренд: D-Link Страницы: 54
Edimax GS-1016 Datasheet preview
GS-1016
Бренд: Edimax Страницы: 2
ORVIBO ZigBee Mini Hub Faq preview
ZigBee Mini Hub
Бренд: ORVIBO Страницы: 3
Western Telematic IPS-800CE-D16, IPS-1600CE-D16 User Manual preview
IPS-800CE-D16, IPS-1600CE-D16
Бренд: Western Telematic Страницы: 58
Wavetronix Click 223 Installation preview
Click 223
Бренд: Wavetronix Страницы: 3
Gefen EXT-DP-EDIDP User Manual preview
EXT-DP-EDIDP
Бренд: Gefen Страницы: 56
GeoVision GV-POE2411-V2 Manual preview
GV-POE2411-V2
Бренд: GeoVision Страницы: 7
Farallon Fast Starlet User Manual preview
Fast Starlet
Бренд: Farallon Страницы: 22
StarTech.com VS221HD20 Quick Start Manual preview
VS221HD20
Бренд: StarTech.com Страницы: 2
Edimax ES-5160G+ Install Manual preview
ES-5160G+
Бренд: Edimax Страницы: 8
Dahua D-PFS3110-8ET1GT1GF-96 Quick Start Manual preview
D-PFS3110-8ET1GT1GF-96
Бренд: Dahua Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды