manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

Front Panel Operation

4-40

Enter-Scan-Count 

 

With this selection, the user deter-

mines the number of scans to perform. You can pro-
gram the Model 7001 to perform from 1 to 9999 scans.
For example, if you enter a scan count of 10, the pro-
grammed scan will be performed 10 times. Perform the
following steps to enter the scan count: 

1. With the NUMBER OF SCANS menu displayed,

place the cursor on ENTER-SCAN-COUNT and
press ENTER. A message indicating the current
scan count will be displayed. 

SCAN COUNT = 0001

The above scan count indicates that the Model
7001 will perform one scan. A value of “0000” indi-
cates that the scan count is set to infinite.

2. To program for a different count (1 to 9999), use the

keypad to enter the count value.

3. With the desired count value displayed, press EN-

TER. The display will return to the SCAN CON-
TROL menu. 

CONTROL  

 

Use this menu item to enable or disable the

source bypass. The source bypass is used to bypass the
scan spacing event on the first pass through the scan.
With the SCAN CONTORL menu displayed, select this
menu item by placing the cursor on CONTROL and
pressing ENTER. The following menu will be dis-
played:

TRIGGER CONTROL 

SOURCE

ACCEPTOR

Source 

 

With this selection, the source bypass is en-

abled. The scan spacing event will be bypassed on the
first pass through the scan layer if EXTERNAL or TRIG
LINK scan spacing is selected. This will allow opera-
tion to proceed on into the channel layer without hav-
ing to wait for the programmed event.

Acceptor 

 

With this selection, the source bypass is dis-

abled.

4.8.3

ARM CONTROL

Arm control is used for the following operations: 

•

To select the arming event (ARM SPACING) for
the scanner. 

•

Designate the number of times the scanner is to be
armed (ARM COUNT)

•

Enable or disable the Source Bypass.

Perform the following steps to display the ARM CON-
TROL menu:

1. Display the CONFIGURE SCAN menu (see para-

graph 4.8, General rule #1). 

2. Use the cursor keys (

 and 

) to place the cursor

on ARM CONTROL and press ENTER to access
the following menu: 

SETUP ARM CONTROL 

ARM-SPACING

ARM-COUNT 

 TRIGGER-CONTROL

ARM-SPACING 

 

This menu item is used to select the

event that controls the arm spacing. To select this menu
item, place the cursor on ARM-SPACING and press
ENTER. The following menu will be displayed: 

ARM SPACING

MANUAL

IMMEDIATE

GPIB 

 EXTERNAL

TRIGLINK

HOLD

Manual 

 

With this selection, the front panel STEP key

is used to control arm spacing. Operation will pass into
the scan layer when the STEP key is pressed.

Note: The front panel STEP key is active when TIMER,
EXTERNAL, GPIB or TRIGGER LINK is selected. 

To select manual triggering (STEP key) from the SE-
LECT ARM SPACING menu, place the cursor on
MANUAL and press ENTER. The instrument will re-
turn to the SETUP ARM CONTROL menu. 

Immediate 

 

With this selection, operation will pass im-

mediately into the scan layer.

Select immediate triggering from the SELECT ARM
SPACING menu by placing the cursor on IMMEDIATE
and pressing ENTER. The instrument will return to the
SETUP ARM CONTROL menu. 

GPIB 

 

With this selection, bus triggers are used to con-

trol arm spacing. Operation will pass immediately into
the scan layer when a bus trigger (GET or *TRG) is re-

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

3Com SUPERSTACK 3 3226 Datasheet preview
SUPERSTACK 3 3226
Бренд: 3Com Страницы: 5
3Com LANPLEX 2500 Operation Manual preview
LANPLEX 2500
Бренд: 3Com Страницы: 139
3Com CoreBuilder 7000 Installation & Start?Up Manual preview
CoreBuilder 7000
Бренд: 3Com Страницы: 150
3Com CoreBuilder 7000 Operation Manual preview
CoreBuilder 7000
Бренд: 3Com Страницы: 264
3Com 4007 Command Reference Manual preview
4007
Бренд: 3Com Страницы: 574
3Com 3CRUS2475 24 User Manual preview
3CRUS2475 24
Бренд: 3Com Страницы: 333
3Com SUPERSTACK 3 3226 Getting Started Manual preview
SUPERSTACK 3 3226
Бренд: 3Com Страницы: 70
3Com OfficeConnect 3C16790C User Manual preview
OfficeConnect 3C16790C
Бренд: 3Com Страницы: 18
3Com 5500-EI PWR Reference Manual preview
5500-EI PWR
Бренд: 3Com Страницы: 1314
3Com SuperStack II Switch 1100 User Manual preview
SuperStack II Switch 1100
Бренд: 3Com Страницы: 62
B&K HD6 User Manual preview
HD6
Бренд: B&K Страницы: 28
B&K HD6 Getting Started Manual preview
HD6
Бренд: B&K Страницы: 2
Field Controls 46112100 Manual preview
46112100
Бренд: Field Controls Страницы: 4
LEGRAND WZ3RL10 Installation Instructions preview
WZ3RL10
Бренд: LEGRAND Страницы: 2
Maipu MyPower S2300-28TC-AC Installation Manual preview
MyPower S2300-28TC-AC
Бренд: Maipu Страницы: 31
Quintum Tenor AXE1600 Specifications preview
Tenor AXE1600
Бренд: Quintum Страницы: 2
Attwood 4204 Installation Instructions preview
4204
Бренд: Attwood Страницы: 2
G&D TradeSwitch2-USB Assembly, Installation And Operation Manual preview
TradeSwitch2-USB
Бренд: G&D Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды