manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

Front Panel Operation

4-35

changes are ignored if an EXIT is performed. When
the CONFIGURE SCAN menu is displayed, press-
ing EXIT will disable SCAN CONFIGURATION. 

3. The position of the cursor is denoted by the blink-

ing menu selection or parameter. The cursor is
moved from one item to the next using the cursor
keys (

 and 

).

4. A displayed arrow (

 or 

) indicates that there

is more information or additional menu items to
select from. When “

” is displayed, use the 

cursor key to display the additional message(s),
and conversely, when “

” is displayed, use the

 cursor key. 

5. A numeric parameter is keyed in by placing the

cursor on the digit to be changed, and pressing the
appropriate key on the keypad. After keying in a
number, the cursor will move to the next digit to
the right. 

6. A parameter change is only executed when the

ENTER key is pressed.

7. ENTERing an invalid parameter generates an error

and ignores the entry.

8. The INFO key can be used anywhere in the menu

structure to display helpful information messages
concerning operation. To cancel an information
message, press EXIT or INFO a second time. 

4.8.1

CHAN-CONTROL

Channel control is used for the following operations: 

•

To select the event that controls the time period
(CHANNEL SPACING) between channel closures
of a scan. 

•

Designate the NUMBER OF CHANS (channels) in
the scan.

•

Enable or disable the Source Bypass.

Perform the following steps to display the CHANNEL
CONTROL menu:

1. Display the CONFIGURE SCAN menu (see para-

graph 4.8, General rule #1). 

2. Use the cursor keys (

 and

 ) to place the cursor

on CHAN-CONTROL and press ENTER to access
the following menu: 

CHANNEL CONTROL  

CHANNEL-SPACING

NUMBER-OF-CHANS 

 CONTROL

CHANNEL SPACING 

 

Use this menu item to select the

event that controls the time period between channel
closures of the scan. With the CHANNEL CONTROL
menu displayed, select this menu item by placing the
cursor on CHANNEL-SPACING and pressing ENTER.
The following menu will be displayed: 

SELECT CHAN SPACING

TIMER

EXTERNAL

GPIB

MANUAL 

 TRIGLINK

IMMEDIATE

HOLD

Timer 

 

Use the timer to control channel spacing. The

timer is used to set a time interval between channel clo-
sures of the scan. The timer can be set for an interval
from zero to 99999.999 seconds with 0.001 second
(1msec) resolution. The first interval begins after the
first channel of the scan closes. Perform the following
steps to use the timer: 

1. With the SELECT CHAN SPACING menu dis-

played, place the cursor on TIMER and press EN-
TER. A message indicating the currently set time
interval (in seconds) will be displayed. If, for ex-
ample the timer is set to 1msec, the following mes-
sage will be displayed: 

INTERVAL = 00000.001

2. To retain the displayed timer interval, press EXIT

or ENTER. The instrument will return to the
CHANNEL CONTROL menu. 

3. To set a different time interval, use the keypad to

key in the value (in seconds) and press ENTER.
The instrument will return to the CHANNEL
CONTROL menu. 

Note: The front panel STEP key (see MANUAL) is ac-
tive with the timer selected. Each press of the STEP key
will select the next channel of the scan. This can be
used to quickly step through a scan that has a relatively
long timer interval.

External 

 

With this selection, external triggers are

used to control channel spacing for the scan. Each trig-
ger stimulus applied to the Model 7001 will open the
current channel and close the next channel of the scan.
The external trigger is applied to the rear panel “EX-
TERNAL TRIGGER” BNC connector. In the external
trigger mode, the Model 7001 can be used to trigger an-
other instrument. After a channel is closed and settled,
a trigger pulse is applied to the rear panel “CHANNEL
READY” BNC connector. This trigger pulse can, for ex-

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Hama 11800 Operating Instruction preview
11800
Бренд: Hama Страницы: 5
3Com SuperStack 3 4900 Datasheet preview
SuperStack 3 4900
Бренд: 3Com Страницы: 2
Eaton COOPER POWER SERIES Maintenance Instructions Manual preview
COOPER POWER SERIES
Бренд: Eaton Страницы: 32
Keithley 2750 User Manual preview
2750
Бренд: Keithley Страницы: 452
LEGRAND WZ3RL10 Installation Instructions preview
WZ3RL10
Бренд: LEGRAND Страницы: 2
Maipu MyPower S2300-28TC-AC Installation Manual preview
MyPower S2300-28TC-AC
Бренд: Maipu Страницы: 31
Sangamo RPTS Q550 Installation & User'S Instructions preview
RPTS Q550
Бренд: Sangamo Страницы: 2
I-Tech JKP115-801e User Manual preview
JKP115-801e
Бренд: I-Tech Страницы: 39
Flowserve PMV WM Ultraswitch User Instructions preview
PMV WM Ultraswitch
Бренд: Flowserve Страницы: 16
Samson 4747 Mounting And Operating Instructions preview
4747
Бренд: Samson Страницы: 64
Black Box ServSwitch 17S Quick Start Manual preview
ServSwitch 17S
Бренд: Black Box Страницы: 10
ORiNG TGS-1080-M12 Series Quick Installation Manual preview
TGS-1080-M12 Series
Бренд: ORiNG Страницы: 2
TRENDnet TK-407K - KVM Switch - USB Specifications preview
TK-407K - KVM Switch - USB
Бренд: TRENDnet Страницы: 2
Santon D1-G/H-T Installation Manual preview
D1-G/H-T
Бренд: Santon Страницы: 16
TRENDnet TE100-S16plus User Manual preview
TE100-S16plus
Бренд: TRENDnet Страницы: 32
QNAP QSW-M1208-8C Quick Installation Manual preview
QSW-M1208-8C
Бренд: QNAP Страницы: 30
EKOBUY ekb10075 User Manual preview
ekb10075
Бренд: EKOBUY Страницы: 8
Raritan MCC8 User Manual preview
MCC8
Бренд: Raritan Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды