Keithley 7001 Скачать руководство пользователя страница 82

Страница: 82 / 353

Front Panel Operation

4-33

1. To change the delay period, use the cursor keys

and the keypad to key in the desired value.

2. With the desired delay displayed, press ENTER. The

instrument will return to the SET DELAY FOR: menu.

4.7.5

READ-I/O-CARD

This menu selection is used to identify if there are any
I/O cards installed in the Model 7001.

1. Display the CARD CONFIG MENU (see para-

graph 4.7, General Rule #1).

2. Place the cursor on READ-I/O-CARD and press

ENTER to display the model number of the I/O

card. If no I/O card is installed, the following mes-
sage will be displayed:

No I/O Cards

3. Press EXIT to return to the CARD CONFIG

MENU.

4.8

SCAN CONFIG

Various operations to configure a scan are performed
from the CONFIGURE SCAN menu. The menu struc-
ture is shown and summarized in Table 4-6 (cont.).

Table 4-6
CONFIGURE SCAN menu structure

Menu item

Description

CHAN-CONTROL Configure Channel Layer:

CHANNEL-SPACING

Select channel spacing:

TIMER

Use a timer to select each channel in the scan.

EXTERNAL

Use an external trigger to select each channel.

GPIB

Use a bus trigger to select each channel.

MANUAL

Use STEP key to select each channel.

TRIGLINK

Use a Trigger Link trigger to select each channel.

ASYNCHRONOUS

Use separate lines for In/Out triggers.

SEMI-SYNCHRONOUS

Use same line for In/Out triggers.

IMMEDIATE

Use to scan channels immediately.

HOLD

Use to hold up the scan in the channel layer.

NUMBER-OF-CHANS Define number of channels to scan:

USE-SCANLIST-LENGTH

Count = number of channel entries in scan list.

CHAN-COUNT User

defined count:

INFINITE

Repeat channel scanning indefinitely.

ENTER-CHAN-COUNT

Count = user defined value (1 to 9999)

CONTROL

Select trigger control mode:

SOURCE

Enable the Source Bypass.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Результаты поиска

Содержание 7001

Отзывы:

Похожие инструкции для 7001

Бренды по названию

Популярные бренды

Keithley 7001, Инструкция по эксплуатации

Результаты поиска

Содержание 7001

Отзывы:

Похожие инструкции для 7001

Бренды по названию

Популярные бренды