Keithley 7001 Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 353

background image

IEEE-488 Reference

5-117

5.17

:SYSTem Subsystem

The system subsystem contains miscellaneous commands and are summarized in Table 5-12.

5.17.1

Table 5-12

SYSTem command summary

Command

Description

Reference

:SYSTem

:PRESet
:POSetup <name>
:POSetup?
:VERSion?
:ERRor?

Return to :SYST:PRES defaults.
Select power-on setup: RST, PRESet, SAV0-SAV9.
Query power-on setup.
Query revision level of SCPI standard.
Query Error Queue.

5.17.1
5.17.2

5.17.3
5.17.4

Notes:
1. Brackets ([ ]) are used to denote optional character sets. These optional characters do not have to be included in the program message. Do not use

brackets ([ ]) in the program message.

2. Angle brackets (< >) are used to indicate parameter type. Do not use angle brackets (< >) in the program message.
3. Upper case characters indicate the short-form version for each command word.
4. At least one sapce is required between a command word and the parameter.

:PRESet

:SYSTem:PRESet

Return to :SYSTem:PRESet defaults

:syst:pres

This command returns the instrument to states optimized for front panel operation. Table 5-5
defines the default conditions for this command.

OUTPUT 707; “:syst:pres”

! Return 7001 to default states

:POSetup <name>

:SYSTem:POSetup <name>

Program power-on defaults

<name> = RST

Select *RST defaults on power up

= PRESet

Select :SYSTem:PRESet defaults on power up

= SAVX

Select saved defaults on power up

where; X = 0 to 9

:syst:pos <name>

Short-form

format

Description

Programming

example

5.17.2

Parameters

Short-form

format

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

«
...
234
235
236
237
238
...
»

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Бренд: ABLE Страницы: 5

Бренд: N-Tron Страницы: 18

Бренд: Belkin Страницы: 12

Бренд: Cabletron Systems Страницы: 52

Instant On 1930 24G 4SFP/SFP+l

Бренд: Aruba Страницы: 48

Бренд: Hamlet Страницы: 2

Бренд: N-Tron Страницы: 169

Бренд: SmartAVI Страницы: 2

Бренд: MicroNet Страницы: 123

Бренд: Zektor Страницы: 30

DCRS-5200 Series

Бренд: Digital China Networks Страницы: 4

Бренд: Epcom Страницы: 2

Бренд: JUKI Страницы: 2

Бренд: Rosewill Страницы: 3

Бренд: Linkskey Страницы: 2

CTRLink EIDX MP Series

Бренд: Contemporary Controls Страницы: 8

Бренд: mind alive Страницы: 16

Бренд: SP Controls Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды