Keithley 7001 Скачать руководство пользователя страница 200 | Manualshive

Страница: 200 / 353

background image

IEEE-488 Reference

5-81

5.13.4

[:ROUTe] subsystem

:FCHannels <list>

[:ROUTe]:FCHannels <list>

Define “forbidden” channel list

<list> = (@ forblist)

where; forblist is the specified list of “forbidden” channels that cannot be closed.

:fch (@

forblist)

Power-up

Last defined “forbidden” channel list

*RST

No effect

:SYSTem:PRESet

No effect

:FCHannels?

Query “forbidden” channel list

Short-form formats:

:fch?

Response message:

List of “forbidden” channels

The :FCHannels <list> command is used to define a list of channels that cannot be closed. The
following examples demonstrate various forms for expressing a forblist:

Forblist

1!1

Single channel (Slot 1, Channel 1).

1!6, 1!18, 2!3!6

Channels separated by commas.

1!2:1!10

Range of channels (2 through 10).

1!2:1!10, 1!20

Range entry and single entry separated by commas.

M36

Channel pattern stored at memory location M36.

A “forbidden” channel list can be cancelled by sending an empty forblist as follows:

:fch (@)

If you specify a channel to be restricted and it is already included in the Scan List and/or a Chan-
nel Pattern, then the entire Scan List and/or Channel Pattern is cleared (lost).

10

OUTPUT 707; “:fch (@ 1!1, 1!4); fch?”

20

ENTER 707; A$

30

PRINT A$

40

END

Line 10

Define the “forbidden” channel list and query the the list.

Line 20

Address the Model 7001 to talk.

Line 30

Display the list.

Parameter

Short-form

formats

Defaults

Query

command

Description

Programming

example

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

«
...
198
199
200
201
202
...
»

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Бренд: Alyseum Страницы: 7

Бренд: Perel Страницы: 4

Бренд: I/O Interconnect Страницы: 27

Бренд: StarTech.com Страницы: 10

Бренд: XtendLan Страницы: 24

Бренд: FS Страницы: 41

Бренд: HIKVISION Страницы: 5

Бренд: C4i Страницы: 7

Бренд: S&S Northern Страницы: 8

Бренд: Velleman Страницы: 8

Бренд: J-Tech Digital Страницы: 13

Бренд: DataParts Страницы: 5

Бренд: Edge-Core Страницы: 60

Бренд: steute Страницы: 10

Palert PX-01 Series

Бренд: JenLogix Страницы: 48

Plug in Digital Time Switch

Бренд: Grasslin Страницы: 88

Бренд: Brightlink Страницы: 17

Moeller IZM Series

Бренд: Eaton Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды