Keithley 7001 Скачать руководство пользователя страница 192 | Manualshive

Страница: 192 / 353

background image

IEEE-488 Reference

5-73

5.12

:OUTPut subsystem

The OUTPut subsystem is used to set polarities for the digital output port. Commands in this subsystem are summarized in Table
5-7.

Table 5-7

OUTPut command summary

Command

Description

:OUTPut

:TTL[1]

:LSENse <name>
:LSENse?

:TTL2

:LSENse <name>
:LSENse?

:TTL3

:LSENse <name>
:LSENse?

:TTL4

:LSENse <name>
:LSENse?

Path to set polarity of digital output line 1:

Select polarity; active high (AHIGh) or active low (ALOW).
Query polarity of line 1.

Path to set polarity of digital output line 2:

Select polarity; active high (AHIGh) or active low (ALOW).
Query polarity of line 2.

Path to set polarity of digital output line 3:

Select polarity; active high (AHIGh) or active low (ALOW).
Query polarity of line 3.

Path to set polarity of digital output line 4:

Select polarity; active high (AHIGh) or active low (ALOW).
Query polarity of line 4.

Notes:
1. Brackets ([ ]) are used to denote optional character sets. These optional characters do not have to be included in the program message. Do not use

brackets ([ ]) in the program message.

2. Angle brackets (< >) are used to indicate parameter type. Do not use angle brackets (< >) in the program message.
3. Upper case characters indicate the short-form version for each command word.
4. At least one space is required between a command word and the parameter.

:LSENse <name>

:OUTPut:TTL[1]:LSENse <name>

Set polarity of line #1

:OUTPut:TTL2:LSENse <name>

Set polarity of line #2

:OUTPut:TTL3:LSENse <name>

Set polarity of line #3

:OUTPut:TTL4:LSENse <name>

Set polarity of line #4

<name> = AHIGh

Set polarity of specified line to active high.

= ALOW

Set polarity of specified line to active low.

:outp:ttl:lsen <name>

:outp:ttl2:lsen <name>

:outp:ttl3:lsen <name>

:outp:ttl4:lsen <name>

Power-up

Active high

*RST

No effect

:SYSTem:PRESet

No effect

Parameters

Short-form

formats

Defaults

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

«
...
190
191
192
193
194
...
»

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Бренд: Hama Страницы: 5

SuperStack 3 4900

Бренд: 3Com Страницы: 2

Crouse-Hinds CEAG KO

Бренд: Cooper Страницы: 12

Бренд: Linksys Страницы: 3

Бренд: Cudy Страницы: 2

Бренд: Waters Network Systems Страницы: 12

Бренд: Accton Technology Страницы: 7

Бренд: Novy Страницы: 12

Бренд: Bircher Reglomat Страницы: 4

Бренд: TP-Link Страницы: 2

Бренд: Quark-Elec Страницы: 10

Thinklogical TLX640

Бренд: Belden Страницы: 48

Бренд: PABX Страницы: 16

Force10 TeraScale C Series

Бренд: Dell Страницы: 1640

Бренд: Dell Страницы: 50

SANSWITCH-10430

Бренд: Burg Wächter Страницы: 11

Бренд: Sams Страницы: 18

Бренд: Yamaha Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды