manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

 

IEEE-488 Reference

 

5-5

 

5.5

Front panel aspects of IEEE-488 
operation

 

The following paragraphs discuss aspects of the front panel
that are part of IEEE-488 operation, including messages, sta-
tus indicators, and the LOCAL key. 

 

5.5.1 Error and status messages

 

Table 4-1 in Section 4 summarizes the error and status mes-
sages associated Model 7001 operation. Note that the instru-
ment may be programmed to generate an SRQ, and
command queries can be performed to check for specific er-
ror conditions.

 

5.5.2 IEEE-488 status indicators

 

The REM (remote), TALK (talk), LSTN (listen), and SRQ
(service request) annunciators show the present IEEE-488
status of the instrument. Each of these indicators is briefly
described below.

 

REM 

 

 

 As the name implies, this indicator shows when the

instrument is in the remote state. Note that REM does not
necessarily indicate the state of the REM line, as the instru-
ment must be addressed to listen with REM true before the
REM indicator turns on. When the instrument is in remote,

all front panel keys except for the LOCAL key are locked
out. When REM is turned off, the instrument is in the local
state, and front panel operation is restored. 

 

TALK 

 

 

 

 

This indicator is on when the instrument is in the

talker active state. The unit is placed in this state by address-
ing it to talk with the correct MTA (My Talk Address) com-
mand. TALK is off when the unit is in the talker idle state.
The instrument is placed in the talker idle state by sending it
an UNT (Untalk) command, addressing it to listen, or with
the IFC (Interface Clear) command. 

 

LSTN 

 

 

 

 

This indicator is on when the Model 7001 is in the

listener active state, which is activated by addressing the in-
strument to listen with the correct MLA (My Listen Address)
command. Listen is off when the unit is in the listener idle
state. The unit can be placed in the listener idle state by send-
ing UNL (Unlisten), addressing it to talk, or by sending IFC
(Interface Clear) over the bus. 

 

SRQ 

 

 

 The instrument can be programmed to generate a

service request (SRQ) when one or more errors or conditions
occur. When this indicator is on, a service request has been
generated. This indicator will stay on until the serial poll byte
is read. See paragraph 5.6.8 for details. 

 

5.5.3 LOCAL key

 

The LOCAL key cancels the remote state and restores local
operation of the instrument.

Since all front panel keys except LOCAL are locked out
when the instrument is in remote, this key provides a conve-
nient method of restoring front panel operation. Pressing
LOCAL also turns off the REM indicator, and returns the
display to normal if a user defined message was displayed.

Note that the LOCAL key is also inoperative if the LLO (Lo-
cal Lockout) command is in effect.

 

5.6

Status structure

 

The status register structure of the Model 7001 is shown in
Figure 5-5. The following information will explain the vari-
ous registers and queues that make up this structure.

 

Table 5-2

 

HP BASIC 4.0 IEEE-488 statements

 

Action

BASIC statement

 

Transmit string to device 07.
Obtain string from device 07.
Send GTL to device 07.
Send SDC to device 07.
Send DCL to all devices.
Send remote enable.
Cancel remote enable.
Serial poll device 07.
Send local lockout.
Send GET to device 07.
Send IFC.

OUTPUT 707;A$
ENTER 707;A$
LOCAL 707
CLEAR 707
CLEAR 7
REMOTE 7
LOCAL 7
SPOLL (707)
LOCAL LOCKOUT 7
TRIGGER 707
ABORT 7

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

La Toulousaine 1400 Installation Manual preview
1400
Бренд: La Toulousaine Страницы: 6
ABLE 6 Series Installation & Maintenance Instructions preview
6 Series
Бренд: ABLE Страницы: 5
D-Link DUB-1340 Datasheet preview
DUB-1340
Бренд: D-Link Страницы: 2
D-Link DKVM-4U Specifications preview
DKVM-4U
Бренд: D-Link Страницы: 2
D-Link DKVM-16 - KVM Switch Manual preview
DKVM-16 - KVM Switch
Бренд: D-Link Страницы: 24
D-Link Dis-200G Series Web Ui Reference Manual preview
Dis-200G Series
Бренд: D-Link Страницы: 161
D-Link Dis-200G Series Quick Installation Manual preview
Dis-200G Series
Бренд: D-Link Страницы: 16
D-Link Dis-200G Series Hw Installation Manual preview
Dis-200G Series
Бренд: D-Link Страницы: 47
D-Link DGS-3130-30PS Quick Installation Manual preview
DGS-3130-30PS
Бренд: D-Link Страницы: 25
D-Link DGS-3100 SERIES Hardware Installation Manual preview
DGS-3100 SERIES
Бренд: D-Link Страницы: 54
D-Link DGS-3100 SERIES Cli Manual preview
DGS-3100 SERIES
Бренд: D-Link Страницы: 220
D-Link DGS-3000-28SC Quick Installation Manual preview
DGS-3000-28SC
Бренд: D-Link Страницы: 24
D-Link DGS-1248T - Switch Manual preview
DGS-1248T - Switch
Бренд: D-Link Страницы: 52
D-Link DGS-1216T - Switch Getting Started Manual preview
DGS-1216T - Switch
Бренд: D-Link Страницы: 42
D-Link DGS-1216T - Switch Quick Installation Guid preview
DGS-1216T - Switch
Бренд: D-Link Страницы: 10
D-Link DGS-1010MP Installation Manual preview
DGS-1010MP
Бренд: D-Link Страницы: 8
D-Link DES-3350SR Command Line Interface Reference Manual preview
DES-3350SR
Бренд: D-Link Страницы: 379
D-Link DES-3326SR Manual preview
DES-3326SR
Бренд: D-Link Страницы: 240

Бренды по названию

Популярные бренды

Загрузить еще бренды