manualshive.com logo in svg

Keithley 4299-1, Руководство по установке

Поделиться
Скачать
Keithley 4299-1 Скачать руководство пользователя страница 6

Model 4299-1 Single-Unit Rack-Mount Kit Installation Instructions 

6 

PA-908 Rev. F April 2021 

 

Prepare the rack 

1.  Install the cage nuts (FA-274) into the front rack holes for the front rack-ear and the half-rack front panel 

(see the following figure). 

2.  Install the cage nuts (FA-274) into the rear rack holes for the rack-mount extension arm (2602-335) on the 

same side as the front rack-ear (2602-355). Make sure the locations selected for the rear rack holes 

correspond to the location selected for the front rack holes. 

Cage nuts for the front rack-ear, half-rack front panel, and rack-mount extension arm should be 

installed into the rails at the same hole spacing (vertical height). Cage nuts for the rack-mount 

extension arm should be installed on the same side as the cage nuts for the front rack-ear (refer to 

Install the instrument topic for more detail). 

Figure 6: Rack-mount extension arm 

 

3.  Secure the rack-mount extension arm (2602-335) to the rear of the rack rail using two Phillips truss-head 

screws (#10-32 × 5/8 PHTRSH). 

Содержание 4299-1










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды