background image

Section 7: Increasing SMU current sourcing ability   Model 2651A High Power System SourceMeter® Instrument User's Manual 

7-16 

2651A-900-01 Rev. A / March 2011 

 

Example program usage 

The functions in this script allow the sweep parameters of the test to be adjusted without having to 
rewrite and rerun the script. A test can be executed by calling the function 

DualSmuRdson(gateLevel, dstart, dstop, dsteps, pulseWidth, pulsePeriod, 

pulseLimit)

 with the appropriate values passed to it in its parameters. 

DualSmuRdson() parameters 

Parameter 

Units 

Description 

gateLevel 

Volts 

The voltage level to hold the gate 

dstart 

Amperes 

The level of the first step in the drain sweep 

dstop 

Amperes 

The level of the last step in the drain sweep 

dsteps 

Not 
applicable 

The number of steps in the drain sweep 

pulseWidth 

Seconds 

The width of the pulse in the drain sweep 

pulsePeriod 

Seconds 

The time between the start of consecutive pulses in the drain sweep 

pulseLimit 

Volts 

The voltage limit of the pulses in the drain sweep 

An example call to this function is as follows: 

DualSmuRdson(10, 1, 100, 100, 500e-6, 50e-3, 10) 

This call will set the gate source-measure unit (SMU) output to 10 V and then sweep the drain of the 
device from 1 A to 100 A in 100 points. The points of this sweep will be gathered using pulsed 
measurements with a pulse width of 500 µs and a pulse period of 50 ms for a 1 percent duty cycle. 
These pulses will be limited to a maximum of 10 V. At the end of the sweep, all SMU outputs will be 
turned off. The resulting data from this test will be returned in a Microsoft

®

 Excel

®

 compatible format 

(you can cut and paste the output from the console) that can be used for graphing and analysis. 

 

 

Содержание 2651A













































































Отзывы: