manualshive.com logo in svg

Kees van der Westen Slim Jim mirage, Руководство пользователя

Поделиться
Скачать
Kees van der Westen Slim Jim mirage Скачать руководство пользователя страница 18

USER MANUAL - operation 

Slim Jim User manual 

 

page 17 

Sub-menu TEMPERATURE SETTING 

In the sub-menu temperature setting you can consecutively adjust the following: 

parameter 

range 

factory  increm. 

unit 

remark 

temperature display 

°C, °F 

°C 

 

 

 

grp 1 temperature 

80.0 .. 99.9°C 

176 .. 212°F 

93.0°C 

199.4°F 

0.1 

°C or °F 

 

grp 2 temperature 

 

grp 3 temperature 

In a Duette there is no group 3. 

steam temperature 

110 .. 130°C 

230 .. 266°F 

125°C 

257°F 

1 

Do NOT set mix-water 
temperature by changing the 
steam boiler temperature 

cup heater* 

0 .. 100 or 70 

0 

1 

% or °C 

the cup-heater is 

OFF at “NO 

HEAT” and “ECO-all” 

show temp. at ECO 

no, yes 

no 

 

 

When “yes” the digit displays will 
show a temperature at ECO. 

* With firmware versions 1.18 (for XPv) and 1.23 (Concerto) or higher the cup-heater has changed to 
sensor-controlled temperature (max. 70°C).  

With earlier firmware versions, the cup heater is time-controlled and should not be set higher than 
15% (15 seconds ON, then 85 seconds OFF). A higher setting will soon activate the overheat safety 
device (75°C) in the cup heater, effectively turning the heat OFF. 

 

Sub-menu VOLUME SETTING 

In the sub-menu volume setting you can consecutively adjust the following: 

parameter 

range 

factory 

increment 

unit 

remark 

water timer 

0.5 .. 15 

4.0 

0.1 

s 

mixed-water is timed. 

touchpad 

Bastone 

 

V1Gr1* 

 

 

50

 t

 

1 

ml 

With Bastone units 
there are only 2 
programmable volumes 
per group. The 
positions with

 t

 are only 

available on a 
touchpad. 
 

V2Gr1 

V1Gr1 

 

100 

V3Gr1 

 

 

150

 t

 

V4Gr1 

V2Gr1 

 

200 

V1Gr2 

 

 

50

 t

 

V2Gr2 

V1Gr2 

15 .. 300 

100 

V3Gr2 

 

150

 t

 

V4Gr2 

V2Gr2 

 

200 

V1Gr3 

 

 

50

 t

 

In a Duette there is no 
group 3. 

V2Gr3 

V1Gr3 

 

100 

V3Gr3 

 

 

150

 t

 

V4Gr3 

V2Gr3 

 

200 

* V1Gr1 means shot volume 1 on group 1; V3Gr2 means shot volume 3 on group 2, etc. 

Note that the volumes can also be set with the aid of the touchpads/Bastone units (see page 15). Only 
when volumes are programmed with touchpad or Bastone, the left group is dominant. 

You can roughly program a shot-volume with the touchpad/Bastone and then fine-tune that volume on 
the control panel (increase or decrease) instead of brewing a new shot. Note that the volume shown 
on the interface is the total volume that passes the flow-meter, it thus also includes the water that 
remains in the coffee puck after the brew (appr. half the weight of the coffee-grinds) and the water that 
flows into the double-spring pre-infusion cylinder (DSPIC: appr. 28 ml). 

Example

 

A double espresso shot will have a dosed volume of about 60(brew) + 10(puck) + 28(DSPIC) = 98ml. 

 

 

 

Содержание Slim Jim mirage


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды